FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page B-14

PDF page 66 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 66
AC 27-1B · B-14Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 4                                                     3/31/2014


without exceeding specification operating values; therefore, a “final run sheet” is created
for every engine produced. Additionally, if needed, arrangements can usually be made
with the engine manufacturer to obtain a torque system calibration for individual
engines. This will further optimize the accuracy of the engines used in the flight test
program. The engine manufacturer will also provide predicted uninstalled power
available for the various power ratings. This information may be derived from an engine
computer “card deck” and from charts and tables in the engine detail installation
manual. These data also provide engine performance for the range of altitudes and
temperatures approved for the engine and include methods for correcting this
performance for installation effects. The parameters contained in a typical “card deck”
are plotted for one engine rating in Figure AC 27.45-4.

           (E) Several installation losses (i.e., power decrements) may be associated
with installing an engine in a rotorcraft. Typical losses are air inlet losses, gear losses,
air exhaust losses, and powered accessory losses such as electrical generators.
Additional flight manual performance considerations are the torque indicating system
accuracy and torque needle split. The predicted uninstalled power available engine
characteristics cannot be assumed to be the actual power available after the engine is
installed in the rotorcraft because this procedure would neglect the installation power
losses.  It is necessary to know the installation losses in order to determine the flight
manual performance. Installation losses are reflected reductions in available power
resulting from being installed in a rotorcraft. These losses usually consist of those
incurred due to engine inlet or exhaust design. The rotorcraft manufacturer conducts
tests to confirm the installed specification engine power available on which published
performance is based. The specific methods used vary widely between manufacturers
but usually include some combination of ground and flight tests. Figure AC 27.45-5 is a
typical installed power available chart for one set of conditions.

           (F) The installed power available is, in most cases, lower than obtained on a
test stand. This is especially true at lower airspeeds where exhaust reingestion may
occur and there are changes in airflow routing. The rotorcraft manufacturer may elect to
determine the installation losses for different flight conditions to take any airspeed
advantages. This is acceptable if, for example, the hover performance is based on the
actual power available from an installed minimum specification engine in a hover.
Likewise, it is permissible for the rotorcraft manufacturer to determine his climb
performance based on the actual power available from an installed minimum
specification engine at the published climb airspeed. This will allow the manufacturer to
take advantage of, for example, increased inlet efficiency.

             (ii) Procedures.

           (A) The installed minimum specification engine power output has been
predicted and calculated for various flight conditions.  It is imperative that the predicted
values be verified by actual flight test. The flight test involves obtaining engine
performance measurements at various power settings, altitudes, and ambient



Page B - 14

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →