FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page B-13

PDF page 65 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 65
AC 27-1B · B-13Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

3/31/2014                                      AC 27-1B, Chg 4


applicant needs to substantiate the total rotorcraft throughout the foreseeable range of
operating temperatures.

             (ii) Procedures.

           (A) The FAA/AUTHORITY is responsible for verifying the effects of
temperature on performance and handling characteristics. A limited flight verification, if
necessary, could include spot checks of hover performance, IGE controllability,
vibration, simulated power failure, static stability, height-velocity, VNE/VD evaluations,
ground resonance, etc. In addition, systems should be evaluated to determine
satisfactory operations.

           (B) Extrapolation or interpolation of test data should only be allowed if the
applicant’s predicted or calculated data is verified by actual test. Extrapolations or
interpolations should not exceed 10°C below or 20°C above those values tested.

      (5) Engine Power - Turboshaft Engine.

            (i) Background.

           (A) The purpose of rotorcraft performance flight testing is to obtain accurate
quantitative flight test performance data to provide flight manual information.

           (B) Flight tests are designed to investigate the overall performance
capabilities of the rotorcraft throughout its operating envelope. This testing furnishes
information to be included in the flight manual and provides a means of validating the
predicted performance of the rotorcraft with a minimum installed specification engine.

          (C) The power used to complete the flight manual performance must be
based on power values no greater than that available from the minimum uninstalled
specification engine after it is corrected for installation losses. A minimum uninstalled
specification engine is one that, on a test stand under conditions specified by the engine
manufacturer, will produce the certificated power at specification temperatures and
speeds. The specification values may be either a rating or limit. Some engine
manufacturers certify an engine to a specified power at a particular engine temperature
or speed rating with higher allowable limits. The limit is the maximum value the installed
engine is allowed in order to develop the specification power. Prior to installation of
each engine in a rotorcraft, the performance is measured by the engine manufacturer.
This is done by making a static test run in a test cell and referring the results to standard
day, sea level conditions. The performance parameters obtained are presented as
uninstalled engine characteristics on a test log sheet. This is commonly referred to as a
“final run sheet.” Figure AC 27.45-3 compares a typical engine to one the manufacturer
has certified as a minimum uninstalled certified engine.

          (D) After engine certification, the engine manufacturer is responsible to
ascertain that each engine delivered will produce, as a minimum, the certified power


                                                          Page B - 13

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →