FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page B-12

PDF page 64 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 64
AC 27-1B · B-12Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 4                                                     3/31/2014


               (8) Engine operating characteristics (§ 27.939).

Specific guidance on test methodology and data requirements is provided in applicable
paragraphs of this guidance section.

           (B) As detailed in paragraph b.(2) above, the maximum allowable
extrapolation of HV, IGE controllability and engine operating characteristics is
±2,000 feet. Therefore, the maximum takeoff and landing altitude presented in the RFM
is not normally more than 2,000 feet above the density altitude experienced at the high
altitude test site, or for CAR 6, Amendment 6-7 and subsequent, unless test results
were demonstrated to at least 7,000 feet.

          (C) If IGE controllability is demonstrated to at least 17 knots of wind at
7,000 feet, hover capability above 7,000 feet may be presented provided that the
maximum demonstrated safe wind for takeoff and landing above 7,000 feet is specified
in the RFM.

          (D) The requirements for data collection and presentation in the RFM vary
depending upon the certification basis of the rotorcraft. These requirements are
presented by regulation and amendment in Figures AC 27.45-1 and AC 27.45-2.

           (E) The maximum takeoff and landing altitude may be extrapolated no
greater than the values given in paragraph b.(2) and not above the lowest limiting
altitude resulting from the requirements of paragraph b.(3)(ii)(A) above.

      (4) Temperature Effects.

            (i) Background.

           (A) In the past, approved analyses were frequently accepted for determining
the extreme temperature effects on performance and flight characteristics. With the
introduction of newer, higher performance rotorcraft, advanced rotor blade designs,
higher airspeeds, and higher blade tip Mach numbers, the previous methods have
proven to be insufficient. Therefore, the performance and flight characteristics should
be validated at extreme temperatures; however, analysis may be permitted if a suitable
methodology is demonstrated.

           (B) Various FAA/AUTHORITY cold weather programs have verified that
rotorcraft can be affected by cold temperature in both the performance and flying
qualities areas. Hot temperature conditions, although not shown to be as critical for
flying qualities, should be given consideration.

          (C) Additionally, design deficiencies surfaced when the rotorcraft were
exposed to temperature extremes and some of these difficulties were severe enough to
require the redesign of equipment and materials. Therefore, to satisfy § 27.1309(a), the


Page B - 12

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →