Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
3/31/2014 AC 27-1B, Chg 4
(ii) As in all testing, extrapolation or interpolation should only be considered if all
available information and engineering judgment indicate that regulatory compliance can
be met at the untested conditions.
(3) Altitude Limitations.
Explanation. Two altitudes are normally presented in the RFM to define the operating
envelope of a rotorcraft: maximum operating altitude and maximum takeoff
and landing altitude.
(A) Maximum operating altitude is an operating limitation required by
§ 27.1527 and delineates the maximum altitude to which operation is allowed. This
altitude normally constitutes the maximum cruise or enroute altitude.
(B) Maximum takeoff and landing altitude may be limited by the IGE hover
ceiling for a rotorcraft as described in § 27.73 (through Amendment 27-14) or by low
speed controllability. The hover ceiling and any information pertinent to takeoff and
landing are presented in the performance information section of the RFM. For rotorcraft
certificated to CAR 6, Amendment 6-7 or any amendment of part 27, a hover ceiling
may not be presented above the altitude at which takeoff, HV, and IGE controllability
tests were conducted plus allowable extrapolation, unless that extrapolated altitude is to
at least 7,000 feet. If the applicant elects to demonstrate these tests to an altitude
below 7,000 feet, including allowable extrapolation, then that altitude is the maximum
takeoff and landing altitude of the rotorcraft. The maximum takeoff and landing altitude
may be coincident with, but never above the maximum operating altitude limitation.
Takeoff and landing and hover ceiling data and presentation requirements are
presented in §§ 27.51, 27.73, and 27.1587.
(ii) Procedures.
(A) In establishing the maximum takeoff and landing altitude, the following
tests are normally required:
(1) Takeoff (§ 27.51).
(2) Climb (§§ 27.65 and 27.67).
(3) Performance at minimum operating speed (§ 27.73).
(4) Landing (§ 27.75).
(5) HV envelope (§ 27.79).
(6) IGE controllability (§ 27.143(c)).
(7) Cooling (§§ 27.1041, 27.1043, and 27.1045).
Page B - 11
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.