FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page B-10

PDF page 62 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 62
AC 27-1B · B-10Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 4                                                     3/31/2014


            (i) Allowable wind conditions will vary with the type of test and will also be
different for different types and gross weight rotorcraft. For example, higher winds can
usually be tolerated for takeoff and landing tests than for hover performance. Higher
winds can sometimes be tolerated during hover performance testing on rotorcraft with
high rotor downwash velocities. Generally, unless the effects of wind on hover
performance tests can be determined and accounted for, hover performance testing
should be conducted in winds of 3 knots or less.

             (ii) IGE controllability and maneuverability testing should be conducted in
surface winds of less than 5 knots, or when higher steady wind conditions exist, with a
maximum gust spread of 5 knots.

              (iii) As can be seen from the foregoing, there is no such thing as an exact
allowable wind for a particular test or rotorcraft. The flight test team must decide on the
allowable wind for each condition based on all available information and their
engineering judgment. The following summary of allowable wind conditions is given for
general guidance only:

           (A) Hover performance - 0 to 3 knots.

           (B) HV - 0 to 5 knots.

          (C) IGE controllability and maneuverability - 0 to 5 knots.

          (iv) A means should be provided to measure the wind velocity, direction, and
ambient air temperature at the rotor height for any particular tests.

      (2) Altitude Effects: Extrapolation and Interpolation.

            (i) Using FAA//AUTHORITY approved methodology:

           (A) Hover performance may be extrapolated from test data up to a maximum
of ±4,000 feet density altitude from the test altitude.

           (B) IGE handling qualities, height-velocity, and engine operating
characteristics may be extrapolated from test data up to a maximum of ±2,000 feet
density altitude from the test altitude.

          (C) Cruise stability and controllability tests should be evaluated at a minimum
at two different altitudes, the lowest practical altitude and approximately the highest
cruise altitude requested for approval. This can allow an interpolation of approximately
10,000 feet density altitude.




Page B - 10

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →