FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page B-9

PDF page 61 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 61
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

3/31/2014                                      AC 27-1B, Chg 4


                     SUBPART B - FLIGHT

                      PERFORMANCE


AC 27.45. § 27.45 (Amendment 27-14) PERFORMANCE - GENERAL.

   a. Explanation.

      (1) Section 27.45 of 14 CFR regulations lists the rules and standards under which
the performance requirements are to be met. This guidance provides general
guidelines that may be used throughout a flight test program.  It is impossible to find
ideal test conditions and there are many variables that affect the flight test results that
must be taken into account. Some of these variables are wind, temperature, altitude,
humidity, rotorcraft weight, power, rotor RPM, center of gravity, etc. A thorough
knowledge of the testing procedures and data reduction methods is essential and good
engineering judgment must be used to determine acceptable test conditions. The test
results should be analyzed and expanded by an approved methodology. The guidance
within this section is considered an approved methodology.

      (2) Performance should be based on approved engine power as determined in
paragraph b.(5) below and not on any transient limits. Approved transient limits are
basically for inadvertent overshoots of approved operational limits, and any sustained
operation in these transient limit areas usually requires some form of special
maintenance. However, for such demonstrations as landing procedure demonstration
and HV determination, low rotor speeds (within approved limits) have been authorized.
Such transients, if authorized, must be flight evaluated.

      (3) Where variations in the parameter on which a tolerance is allowed will have an
appreciable effect on the test, the results should be corrected to the standard value of
the parameter; otherwise, no correction is necessary.

      (4) The 30-second and 2-minute OEI power ratings, defined in 14 CFR 1.1, are
based on up to three periods of use during a single flight. The purpose of the three
periods is (i) to initially recover from an engine failure, (ii) to conduct OEI missed
approach, and (iii) to conduct the final OEI landing. Rotorcraft performance based on
the use of these time-limited power ratings is only permitted once in each of the above
three periods (i.e., 30-second power must not be used more than once during the initial
recovery from an engine failure).

      (5) All engines operating (AEO) performance must be based upon approved AEO
power ratings. OEI power ratings cannot be applied to an AEO condition.

   b. Procedures.

      (1) Winds for Testing.


                                                           Page B - 9

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →