FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page F-80

PDF page 689 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 689
AC 27-1B · F-80Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

alert the crew to the capabilities of the aircraft when operating in icing conditions.
Avoidance procedures (e.g., climb or descent) may also be useful.

         (6) Flight Test Prerequisites.

                  (i)   The prototype rotorcraft should be certified (or in the process of being
certified) for IFR flight.

                   (ii)    Sufficient analyses should be developed, submitted, and accepted by
the FAA/AUTHORITY to show that the rotorcraft is capable of safely operating to the
selected design points of both the continuous maximum and intermittent maximum
conditions of Part 29, Appendix C, or the altitude-limited icing envelope. A detailed
failure modes and effects analysis (FMEA) of the ice protection system should be
performed.

                    (iii)   Specific attention should be given to (1) assuring that the selected
design condition(s) of atmospheric and rotorcraft flight envelopes have been identified;
(2) qualification and design of ice protection systems and components; and (3)
component installation and ice formation effects upon basic rotorcraft structural
properties and handling qualities. These assurances can be established from analyses,
bench tests, and/or dry air flight tests or simulated icing tests, as appropriate, prior to
flight tests in natural icing.

               (iv)  The applicant should assess rotor blade stability with ice deposits to
assure that dynamic instability will not occur in icing conditions. This assessment may
be accomplished by analysis including consideration of failure of the most critical
segment of the rotor blade ice protection system.  It also may be accomplished by
experimental means such as attaching dummy ice shapes to the blades and using a
whirl stand or wind tunnel.

      c. Procedures.

         (1) Compliance.

                  (i)    In general, compliance can be established when there is reasonable
assurance that while operating in the specified icing environment (1) the engine(s) will
not flameout or experience significant power losses or damage; (2) stress levels are not
reached with ice accumulations that can endanger the rotorcraft or cause serious
reductions in component life; (3) the handling qualities, performance, visibility, and
systems operation are defined and are not deteriorated unacceptably; (4) inlet, vent, or
drain blockage (such as fuel vent, engine, or transmission cooler) is not excessive; and
(5) autorotation characteristics are acceptable with maximum ice accretion between
deice cycles. Assessment of performance loss should include not only the drag and
weight of the ice itself but electrical or other load demands of the ice protection system
and any performance changes resulting from modified rotor blade contours.



Page F - 80

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →