Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/30/99 AC 27-1B
(ii) It is emphasized that ice formations (shape, weight, etc.) vary
significantly under varying conditions of OAT, LWC, MVD, airspeed, attitude, and rotor
RPM. The most critical conditions should be defined by means of analyses or test and
verified by test. Performance changes under these various conditions should be
determined and found acceptable.
(iii) Laboratory, icing tunnel, ground spray rig, and airborne icing tanker
tests are all very useful in developing an ice protection capability, but none of these,
either individually or collectively, can satisfy the full requirements for certification. None
can presently duplicate the combinations of liquid water content, droplet size, flow field,
and random shedding patterns found in natural icing conditions. Airborne tankers hold
considerable promise of being able to fulfill certification requirements (in addition to the
advantage of being able to produce an icing environment on demand rather than having
to wait for it to occur in nature), but tankers have not been able to generate droplet sizes
that cover the complete envelope for certification. Many improvements have been
made in some tankers in recent years; however, large droplet sizes have typically been
a problem. Also, the size of existing tanker clouds is not of sufficient cross section to
immerse the entire rotorcraft. There are also solar radiation and relative humidity
effects to be considered and correlated with natural icing when using a tanker. The
tanker should be able to immerse the entire rotor system as a minimum and should
have a means of controlling and changing the cloud characteristics uniformly and
repetitively. Until an artificial method has been successfully demonstrated and
accepted, icing certification must include flight tests in natural icing conditions.
(iv) Flight testing in natural icing conditions also has limitations.
Reference AC 27.1419d(16) contains information that may be useful in planning natural
icing flight tests. The key limitation of natural icing flight tests is being able to find the
combinations of conditions that comprise critical design points. This is especially true of
those points falling near the 99.9 percentile of exceedance probability; e.g., high LWC at
low OAT with large MVD. It is emphasized that some more severe design points,
however, may exist within the atmospheric icing envelope rather than near the edges or
corners of the envelope. This does not mean that natural icing tests must be conducted
at all the selected design conditions. Natural icing tests should be conducted in
conditions as close to design points as possible and sufficient correlation shown with
the analyses to assure that the rotorcraft can operate safely throughout the design
envelope.
(v) Certification flight testing should be extensive enough to provide
reasonable assurance that either induced or random ice shedding does not present a
problem. The most likely indication of a problem if it exists will be ice impact on the
airframe or rotor imbalance resulting in vibration. The following should be considered
sufficient for rejection:
(A) Vibrations sufficient to make the instruments difficult to read
accurately.
Page F - 81
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.