FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page F-79

PDF page 688 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 688
AC 27-1B · F-79Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

effect on the air traffic system and would still be operationally useful. Figures 3 and 6 of
Appendix C, Part 29, relate the variation of average LWC as a function of cloud
horizontal extent. These relationships should be used for design assessment of the
most critical combinations of conditions as a function of en route distance. This, in
combination with a capability to hold in icing conditions for 30 minutes at the destination,
is commensurate with policies previously established for fixed-wing aircraft. Figures 3
and 6 should be used in conjunction with the altitude-limited criteria of figures AC
27.1419-1 through -4 herein.  It is emphasized that LWC extremes expressed in
Part 29, Appendix C, criteria represent the maximum average values to be anticipated
within an exceedance probability of 99.9 percent. Transient, instantaneous peak values
of much higher LWC have been observed. These instantaneous peak values appear to
be of little significance to the design of protected and unprotected surfaces; however,
these high values, if encountered, may induce shedding of ice from some unprotected
surfaces. This is due to radical changes in the rate of release of latent heat and
resultant changes in the structural properties and adhesion force of ice.

                    (iii)  An analysis performed at the FAA Technical Center in 1985 concludes
that the aircraft icing environment below 10,000 feet is not as severe in terms of LWC
and OAT as that depicted in the Part 29, Appendix C, envelope. This AC presents the
altitude-limited envelope that may be employed by those applicants who elect to certify
with a 10,000-foot pressure altitude limit. The altitude-limited envelope is based upon
the same data that were used to derive the design criteria of Part 29, Appendix C
(figures AC 27.1419-1 through -4). The data used to derive these limited envelopes
cannot be used to further define icing conditions between 10,000 feet and 22,000 feet;
hence, above 10,000 feet, the Part 29, Appendix C, envelopes should be used.  It
should be noted that the engine inlets should still meet the icing requirements of
§ 27.1093. The limited icing envelopes may be used on an equivalent safety basis to
show compliance with the intent of § 27.1093 if the altitude limit established for the
rotorcraft is not greater than 10,000 feet.

               (iv)   Significantly different effects can result from various combinations of
parameters. For example, most rapid ice accumulations occur at the high values of
liquid water content, although the greatest impingement area occurs at the high values
of droplet size. Most critical ice shapes are a function of each of these parameters in
addition to airspeed, surface temperature, and surface contour. Care should be taken
to explore the entire specified ranges of these parameters during the design,
development, and certification efforts.

              (v)   Mixed conditions (i.e., a combination of ice crystals and supercooled
water droplets) and freezing rain or freezing drizzle are not addressed in the Part 29
environmental criteria but can present more severe icing conditions than those defined.
Although the probability of encountering freezing rain is relatively low, mixed conditions
commonly occur in supercooled cloud formations.  Little data have been gathered on
the effects of encountering mixed conditions (see paragraph AC 27.1419d(6). There
are no criteria for certification in mixed conditions or freezing rain at present and
therefore any icing certification is only valid for supercooled droplets. The RFM should


                                                       Page F - 79

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →