FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page F-73

PDF page 682 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 682
AC 27-1B · F-73Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

4/25/06                                        AC 27-1B, Chg 2


         (4) Stowage provisions for signaling equipment required by § 27.1415 should
be located near a designated ditching emergency exit.

         (5) If stowage provisions for life preservers are included in an interior
configuration, each life preserver when stowed must be within easy reach of each
occupant while seated.

         (6) Service experience has shown that following deployment, life rafts are
susceptible to damage while in the water adjacent to the helicopter due to projections
on the exterior of the helicopter such as antennas, overboard vents, guttering, etc.
Projections likely to cause damage to a deployed life raft should be modified or suitably
protected to minimize the likelihood of their causing damage to a deployed life raft.
Relevant maintenance information should also provide procedures for maintaining such
protection for rotorcraft equipped with life rafts.

AC 27.1413 § 27.1413 (Amendment 27-25) SAFETY BELTS.

     a. Explanation. Design and performance standards are contained in this section.

         (1) Each safety belt must be equipped with metal-to-metal latches
(Amdt. 27-15).

         (2) Belts and belt anchors must sustain without failure ultimate loads as
prescribed for each installation.

         (3) Seats and berths are included.

         (4) Litters, if installed, shall be included.

         (5) TSO-C22, Safety Belts, contains acceptable aircraft belt standards. Also,
TSO-C114, Torso Restraint Systems, dated March 27, 1987, contains acceptable
aircraft standards for compliance to the standard per Amendment 27-25, dated
November 13, 1989. In part, the belts shall have a 2-inch nominal width, shall be
self-extinguishing per § 25.853(a), and may have a 1,500- or 3,000-pound rated
strength.

     b. Procedures.

         (1) TSO-C22 or TSO-C114 approved seat belts or seat belt/harnesses should
be used. The rated load shall not be exceeded. During an interior compliance
inspection, the belt should be checked for label, rating, and metal-to-metal latches.

         (2) The type design data shall contain an analysis or test results of belts and
anchors proving compliance with the strength standards of this section. Fitting factors
prescribed in § 27.785 shall be used.


                                                       Page F - 73

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →