Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
(2) Stowage provisions for safety equipment shown to be compatible with the
vehicle configuration presented for certification should be provided and identified so
that:
(i) Equipment is readily accessible regardless of operational
configuration.
(ii) Stored equipment is free from inadvertent damage from passengers
and handling.
(iii) Stored equipment is adequately restrained to withstand the inertia
forces specified in § 27.561(b)(3) without sustaining damage.
(3) Liferaft stowage provisions should be sufficient to accommodate rafts for the
maximum number of occupants for which certification for ditching is requested.
(i) Liferafts stowed inside the rotorcraft should be located near the
ditching emergency exits so that:
(A) Liferafts are readily accessible and deployment through ditching
emergency exits by passengers and crew may be accomplished without unreasonable
effort and training.
(B) Deployment of liferafts can be accomplished without damage (i.e.,
punctures, tears, etc.).
(ii) Liferafts stowed outside of the rotorcraft should have-
(A) A readily accessible deployment device; and
(B) A secondary method of deployment near the stowed area.
(iii) Rotorcraft fuselage attachments for the liferaft static lines required by
§ 27.1415(c) must be provided.
(A) Static line fuselage attachments should not be susceptible to damage
when the rotorcraft is subjected to the maximum emergency ditching water entry loads
established by § 27.801. (See paragraph AC 27.801b(1).)
(B) Static line fuselage attachments should be structurally adequate to
restrain a fully loaded raft of the maximum capacity required for ditching certification.
(C) Liferafts that are remotely or automatically deployed must be attached
to the rotorcraft by the required static line after deployment without further action from
the crew or passengers.
Page F - 72
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.