FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page F-67

PDF page 676 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 676
AC 27-1B · F-67Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

                   SUBPART F - EQUIPMENT

                             LIGHTS


AC 27.1381. § 27.1381 INSTRUMENT LIGHTS.

     a. Explanation. This section provides minimum performance standards for the
instrument lighting system. Section 27.1309(b) is used to evaluate the malfunction
aspects of the system.  If appropriate, § 27.1309(a) is used to evaluate the equipment
under appropriate environmental considerations.

     b. Procedures.

         (1) The overall instrument lighting system should be designed and installed
such that single failures that occur will not result in the loss of both primary and
secondary (backup) lighting for any instrument or area of the cockpit. In some
instances, the system is divided such that the controls for the pilot’s panel are separate
from the copilot’s panel and both of these are separate from the center panel. The ideal
is to divide the system such that the impact of single failures will be minimized.

         (2) Secondary (backup) instrument lighting should be provided, and this is
accomplished in some instances by eyebrow lights. A system that provides general
cockpit lighting from a source in the aft area of the cockpit is normally not acceptable
since normal positioning and movement of the crew will block this type of light.

         (3) The standard does not specify any color requirements for instrument
lighting. White is normally provided. The color provided should ensure that the color
coding of the instruments is readily identifiable.

         (4) The final installed system should be evaluated by a flight test pilot. An
actual night flight should be conducted for initial certification of an aircraft. In some
instances the vibration characteristics and other flight-induced factors have been
demonstrated to seriously affect the pilot’s ability to see in the cockpit environment at
night. Evaluations following modifications may be conducted with a darkened cockpit
on the ground.  It should be verified that direct rays are shielded from the pilot’s eyes,
and that objectionable reflections do not exist. The pilot should also assume failures of
various controls, electrical busses, etc., to account for all appropriate failures.

AC 27.1383. § 27.1383 LANDING LIGHTS.

     a. Explanation. This section provides minimum performance standards for the
installation and normal operation of the landing lights. Certification to this standard is all
that is required for approval of the rotorcraft; however, the different operating rules
should also be reviewed since they may contain additional requirements. The
malfunction considerations are based on the provisions of § 27.1309(b).


                                                       Page F - 67

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →