Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 4 3/31/2014
(iv) The stiffness and permanent set (memory) of KAPTON® may cause
chafing in unrestrained bundles or where KAPTON® insulated wire is bundled with
wires of other insulation types.
(v) Care should be exercised in the stripping, stamping, and terminating
of KAPTON® insulated wires.
NOTE: KAPTON® is a registered trademark of E.I. Du Pont de Nemours and Company.
(6) Compliance to the flame resistance requirement should be shown by testing
in accordance with FAR 25, Appendix F, Part 1, paragraph (b)(7) for the sixty-degree
burn test. FAR 25, Appendix F contains test procedures and pass-fail criteria for this
requirement.
AC 27.1367. § 27.1367 SWITCHES.
a. Explanation. Qualification data that are available from the switch manufacturer
should provide information regarding contact ratings and environmental limitations.
b. Procedures.
(1) Contact ratings are normally provided by the switch manufacturer. If the
particular application is not specifically addressed by the switch manufacturer, additional
information is available in Chapter 11, Section 2 of Advisory Circular 43.13-1A,
“Acceptable Methods, Techniques and Practices: Aircraft Inspection and Repair.”
(2) The rule requires all switches to be accessible.
(i) For operation by a single pilot with seat belt and shoulder harness
normally adjusted, the pilot should be able to identify and operate essential switches
while flying the rotorcraft. Essential system switches should be located forward of a
vertical plane passing left to right (laterally) through the pilot’s body.
(ii) For a crew of two, switches for essential systems can be further back
and beyond the reach of the pilot if readily identifiable and accessible to the other pilot
or crewmember.
(3) This paragraph requires labeling of all switches. Each switch should be
labeled for the circuit controlled, and each switch position should also be labeled.
Page F - 66
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.