FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page F-65

PDF page 674 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 674
AC 27-1B · F-65Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

3/31/2014                                       AC 27-1B, Chg 4

AC 27.1365. § 27.1365 ELECTRIC CABLES.

     a. Explanation. The FAA does not have a wire standard and, in general, relies on
military specifications. Where a military specification does not exist, manufacturers’
specifications, along with appropriate qualification test data, have been accepted.

     b. Procedures.

         (1) Chapter 11 of Advisory Circular 43.13-1A, “Acceptable Methods,
Techniques and Practices: Aircraft Inspection and Repair,” contains a listing of wiring
that has been accepted for aircraft installations.

         (2) In many instances, references to a basic specification are not adequate
since several configurations may exist, and reference to a supplemental specification
sheet will also be necessary.

         (3) Where wire with thin wall insulation (thickness of at least 10.5 mils.) has
been used, some problems can occur if special precautions are not taken when the wire
is stamped for identification. The areas of concern are temperature, pressure, and
dwell time of the stamp.

         (4) Some additional types included in Tables A-I and A-II of MIL-W-5088H,
Appendix A, have also been evaluated and accepted for civil applications. Use of a
specific type of wiring selected from this listing should be coordinated with FAA
engineering personnel.

         (5) Wire insulated with KAPTON® polyimide film manufactured to
MIL-W-81381A, has been used in aeronautical products with varying degrees of
success. The U.S. Navy had such a bad service history with KAPTON® insulated
interconnect wire in aircraft that in the mid-1980s the U.S. Navy no longer allows the
use of KAPTON® insulated wire. U.S. Army policy also bans the use of KAPTON® wire
in their rotorcraft. Although the FAA has taken no such action, the use of KAPTON®
insulated wire requires very special handling. The following areas should be observed
when utilizing KAPTON® insulated wire:

                  (i)   The instructions in the KAPTON® wire “Handling Manual” should be
strictly followed. This manual may be obtained from E.I. Du Pont de Nemours and
Company, Polymer Products Department, Industrial Film Division, Wilmington,
Delaware 19898.

                   (ii)  Use in special wind and moisture problem (SWAMP) areas, such as
wheel wells, usually requires additional protection for the cable bundles.

                    (iii)  The wire should not be exposed to a combination of either high stress
(U.V. or physical) in the presence of water, high humidity, or high PH factor liquids.



                                                          Page F - 65

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →