FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page F-63

PDF page 672 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 672
AC 27-1B · F-63Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

3/31/2014                                      AC 27-1B, Chg 4

devices should be designed to require a manual operation to restore service after
tripping. Circuit breakers must be designed such that the tripping mechanism cannot be
overridden by the operating control. These are known as the “trip free” type.

         (3) This section requires protective devices for circuits essential to safety in
flight to be accessible to the flight crew in the cockpit. These devices should be also
readily accessible to the flight crew in the event it becomes necessary to manage
smoke caused by an electrical failure. Their accessibility should also permit the flight
crew to easily determine if they are in the “tripped” position prior to flight. Again, this
generally applies to systems required for compliance as discussed above.  If continued
safe flight to the destination is sufficiently assured, certain required circuits have been
excepted from this accessibility. Voltmeter and ammeter circuit protective devices are
examples of ones that have been excepted. Some utilization systems, although not
specifically required by part 27, may be required for the particular design to be certified.
Circuit protective devices for these systems should be accessible. The following are
considered acceptable compliance with the “readily reset” provision of this guidance:

                  (i) For operation by a single pilot with seat belt and shoulder harness
normally adjusted, the pilot should be able to identify and reset or replace the opened
circuit protector while flying the rotorcraft. Circuit protection should not be located aft of
a vertical plane passing left to right (laterally) through the pilot’s body.

                   (ii) For a crew of two, it is satisfactory for one crewmember to move his seat
and loosen his shoulder harness to identify and reset or replace the circuit protective
device.  It is not satisfactory for one of the crewmembers to leave his seat to reset or
replace the circuit protective device.

         (4) A switch is a device intended for regular use to open or close a circuit. A
circuit breaker is a device that protects a circuit by opening automatically at a
predetermined current overload. Systems should be designed such that the primary
means to remove or reset the power supply in normal operations is by means of a
switch. The use of a circuit breaker for such normal operations is unacceptable, as it is
not being used for its intended function.

Note:  A switch-rated circuit breaker may be used for this function if it can be shown to
be suitable for the number of switch cycles expected to be performed during the service
life of the system.

         (5) The spare fuse requirement applies only to fuses protecting systems
required to show compliance with the regulations. Spare provisions need not be made
for non-required convenience type installations, although it is encouraged. The spare
fuses should be stored in a location readily accessible to the crew. For spare fuses not
directly visible to the crew, location information should be provided. One acceptable
location is on the fuse panel in a holder without wire terminations. The spare fuse
should be identified “spare” with the fuse rating.



                                                          Page F - 63

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →