Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
6/23/23 AC 27-1B, Chg 9
complying with Objective 3 include using the tests required by the MOC for Objectives
1, 2 and 7 to demonstrate that all emitted gasses are contained or vented overboard
through designed ports. Objective 3 does allow explosive and toxic gases to be
uncontained and not vented overboard if they do not accumulate in hazardous
quantities within the rotorcraft. If you choose to use the test data to demonstrate
compliance by this means, explain how you will demonstrate that hazardous quantities
of gases will not accumulate within the rotorcraft. If your design will have ports to vent
gases overboard, ensure there is a means to protect ground personnel from exposure
to these gases.
iii. MOC for Objective 4: Section AC 27.863 of this guidance,
subparagraph (c), provides an acceptable method of compliance for flammable fluids.
iv. MOC for Objective 5:
(a) Show that if fluid escapes the battery, it is not corrosive or it is
managed in a way (e.g., contained, isolated or vented overboard) that protects the
surrounding structure and adjacent systems, equipment, and electrical wiring.
(b) Any failure of the battery includes, but is not limited to, internal
and external short circuit. See the tests listed in the MOC for Objectives 1, 2, and 7 for
Failure Conditions that are evaluated.
v. MOC for Objective 6:
(a) Force a cell in the battery into thermal runaway by conducting
the RTCA Document DO-347, section 2.3.15, Thermal Runaway Containment Test.
Perform step e. of test method 2.3.15.1 in lieu of steps c. and d. when conducting this
test.
(b) Show that the effects of the heat and any related effects do not
constitute a hazard to the structure or systems of the rotorcraft. If the effects of the heat
or any related effects constitute a hazard to the structure or systems of the rotorcraft,
design mitigation at the aircraft level may be applied to bring the design into compliance
with Objective 6.
vi. MOC for Objective 8: A well designed disconnection system will
function during the tests required by the MOC for Objectives 1, 2, and 7, except for the
test in RTCA Document DO-347, section 2.3.9, where the protection is already disabled.
This is one of the means of preventing the Failure Conditions discussed in the
Evaluation Criteria sections of RTCA Document DO-347 for these tests. Confirm the
battery automatically disconnects from its discharging circuit during these tests.
Page F - 62.10
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.