Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
6/23/23
AC 27-1B, Chg 9
guidance for obtaining installation approval for installed rechargeable lithium battery and
battery systems on rotorcraft.
(B) Installation requirements for installed non-rechargeable lithium batteries
have some common attributes with rechargeable lithium batteries. These batteries
usually exhibit less capacity and a hazard risk proportional to the capacity, but may also
supply a critical and required function.
1. Each non-rechargeable lithium battery installation should address the
following ten objectives, which are critical for safe installation:
Objective 1: Maintain safe cell temperatures and pressures under all foreseeable
operating conditions to prevent fire and explosion.
Objective 2: Prevent the occurrence of self-sustaining, uncontrollable increases
in temperature or pressure.
Objective 3: Prevent any emission of explosive or toxic gases that may
accumulate in hazardous quantities, either during normal operation or as a result
of a failure.
Objective 4: Meet the flammable fluid fire protection requirements of § 27.863.
Objective 5: Prevent corrosive fluids or gases that may escape from damaging
surrounding structure or adjacent systems, equipment, or electrical wiring.
Objective 6: Prevent any hazardous effect on rotorcraft structure or systems
caused by the maximum amount of heat generated from any battery or individual
cell failure.
Objective 7: Automatically control the discharge rate of each cell to prevent cell
imbalance, back charging, overheating, and uncontrollable temperature and
pressure.
Objective 8: Automatically disconnect the battery in the event of an over-
temperature condition, cell failure, or battery failure.
Objective 9: Alert the flight crew if an equipment state or failure affects safe
operation of the rotorcraft.
Objective 10: Have a means for the flight crew to determine the battery charge
state (for required battery systems).
Note: A battery system consists of the battery and any protective, monitoring,
and alerting circuitry or hardware inside or outside of the battery. It also includes
vents (where necessary) and packaging.
Page F - 62.8
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.