Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 9
6/23/23
(vii) For battery replacement with any battery other than the one that was
installed and accepted as part of the original type design, consideration of several
aspects of battery design and installation is important to ensure that the type design is
not negatively impacted.
(A) The replacement battery should provide at least the minimum usable
capacity as required by the current load analysis. This requirement of minimum usable
capacity should be valid over the entire range of environmental conditions. Different
types of batteries have different inherent characteristics. Ni-CAD batteries have a
voltage discharge curve that allows most of the amp-hour capacity to be usable from a
delivered voltage standpoint, where only about 66% of the amp-hour capacity for lead
acid batteries is usable due to the delivered voltage becoming too low to use. If a
replacement battery has a similar discharge rate, and the capacity is similar throughout
the original battery’s environmental range, then no further testing should be needed.
(B) An analysis for a replacement or system modification may be needed
to show that the electrical system still complies to the original operation under IFR and
Category A certification requirements for rotorcraft that depend on fault clearing
features. Subsequent analysis validation by testing may be needed in those cases
where the system that provides fault clearing is difficult to evaluate by analysis alone. In
these cases, the effects of a change in battery internal impedance on the fault clearing
features is uncertain and may not be adequately determined by analysis. There are high
rate discharge types of batteries and slow-rate discharge batteries that have different
internal impedances and their behavior in a fault clearing circuit is also different. The
regulatory basis for analysis and testing for fault clearing is contained in Appendix B to
part 27 and appropriate Category A requirements.
(viii) There are widespread applications of batteries utilizing various lithium
chemistries in aircraft today. These batteries are used as the main start battery and can
be found integrated into various equipment installations. They furnish independent back
up power to required equipment and many non-required applications such as
entertainment systems. There are several different lithium battery chemistries available
with a range of stability. Some of these lithium chemistries have been shown to be
relatively unstable with failure modes that can result in explosive thermal runaway under
certain conditions. A hazard analysis and system safety analysis should be
accomplished, and design mitigation features should be tailored to mitigate hazards
associated with the particular application.
(A) An acceptable means to show compliance with the § 27.1353
airworthiness requirements for installed rechargeable lithium battery and battery
systems on rotorcraft is found in AC 20-184, Guidance on Testing and Installation of
Rechargeable Lithium Batteries and Battery Systems on Aircraft. AC 20-184 provides
Page F - 62.7
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.