FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page F-60

PDF page 656 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 656
AC 27-1B · F-60Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 1                                                           2/12/03

require frequent battery maintenance activities. Future battery installation designs
should not depend on the use of frequent battery maintenance as a compensating
factor for designs that are inherently deficient in battery charging capability. Battery
charging from the helicopter bus voltage is the prevalent method used to charge
batteries, since no separate battery charger is needed. However, for the 20 cell Ni-CAD
example, using the helicopter bus voltage as the battery charging source can introduce
battery capacity limitations. Several options are available to address these concerns.
One option would be to go to a 19 cell battery. Since Ni-CAD batteries were first
introduced, much has been learned about their care and use, plus design improvements
have been made that lessen the possibility of thermal runaways. Another approach
could be to oversize the battery capacity recognizing that the battery will be in a "less
than" nominal capacity condition. This philosophy would also carry with it a Certification
Maintenance Requirement as a limitation on the helicopter approval. Compliance could
be shown by using a dedicated battery charger, that can profile the charging based on
state of charge. This can be much more efficient and make it possible to have a better
charged battery with less frequent maintenance, and increased battery life.

             (C) One of the significant design issues associated with batteries is the
internal impedance. Low internal impedance usually characterizes batteries capable of
high discharge rates. Starting and fault clearing requirements are typically best satisfied
by batteries with low internal impedance. The other extreme is batteries with high
internal impedances that are generally more economical and perform low rate, long-time
interval discharges well. This type of batteries can provide the emergency power for
equipment efficiently.  If both starting/fault clearing and emergency power requirements
are to be provided using a single battery, a workable compromise on the internal
impedance must be accomplished.

             (D) The battery must be qualified to the helicopter’s defined environmental
specifications associated with the battery installation location, as a minimum. High level
environmental qualification may preclude the installation location dependency for the
battery. In addition to the environmental qualification, the design/installation design
should consider the risk of explosion presented by the natural production of gases. An
explosive resistant case or container is an acceptable way of showing compliance to the
rule requiring that the structure and essential systems do not suffer hazardous effects.
There may be other ways to show compliance, but use of the explosion-resistant case is
the predominant way at this time.

                   (ii)   The part of the battery installation approval associated with installation
into the helicopter should consider the adequacy of the associated battery interface
components and the physical aspects of installing the battery.

              (A) The adequacy of the associated components that are necessary to
interface with the battery to provide functionality must be shown to perform their
intended function for the installation environment and operations. These components
should be qualified to meet the most severe environment of their installation and



Page F - 60

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →