Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/30/99 AC 27-1B
(3) Annunciator Panel Arrangement. The annunciator panels should be
arranged in a logical manner to reduce the crew’s time required to locate faults and to
increase their efficiency in following aircraft flight manual procedures. For example,
engine annunciators on multiengine rotorcraft should be physically located on the panel
to coincide with engine location (left or right) so that properly operating engines are not
inadvertently shut down due to crew confusion over which engine has malfunctioned.
AC 27.1323. § 27.1323 (Amendment 27-13) AIRSPEED INDICATING SYSTEM.
a. Explanation.
(1) The accuracy of all flight test data concerned with the velocity of the
rotorcraft is dependent on the calibration of the airspeed indicating system. For this
reason, the airspeed system position error should be determined very early in the
program.
(2) Since air density varies with altitude, the speed reading will only be correct
under standard sea level conditions. However, in an actual installation, the indicator
reading, even under standard sea level conditions, may differ from the calibrated
airspeed because the static system does not sense true static pressure. This error in
detection of static pressure is called position error. It is caused by the pressure field
built up around the rotorcraft in flight. This pressure field will vary in intensity with
dynamic pressure making the position error a function of calibrated airspeed. Since
airspeed information is presented to the crew in terms of indicated airspeed, it is
necessary to determine the position error for the rotorcraft to be flown safely.
b. Procedures.
(1) There are different methods to determine position error such as trailing
bomb, airspeed course, boom system, etc. Each method has its own advantages and
disadvantages, but will yield satisfactory results if done correctly. The airspeed system
should be calibrated throughout the airspeed range of the rotorcraft and under the
various flight conditions of cruise, climb, and autorotation. In addition, the effects of
gross weight and center of gravity should be investigated.
(2) It may also be necessary to recalibrate the system with a change in external
configuration if such a change may affect the airflow near the pitot or static sources.
(3) Additional information regarding position error is included in
paragraph AC 27 Appendix B b(10) and should be considered if pursuing an
IFR approval.
(4) Static system installation information is included in paragraph AC 27.1325.
Technical Standard Order (TSO) C16, Airspeed Tubes (Heated), gives minimum
Page F - 39
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.