Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
causes the associated panel segment to illuminate. At this time all panel segments
connected to the test circuit will illuminate.
(iii) This configuration becomes a special problem when one or more of
the panel segments are red. A red light calls for immediate action by the crew, and the
crew does not have adequate information for immediate action when many false panel
segments are illuminated.
(iv) If the design review indicates a problem, a redesign of the panel to
eliminate the condition is considered to be the best solution and is highly encouraged.
(2) Procedures.
(i) An alternative to panel redesign might be the following:
(A) Review the annunciator panel design and note which segments are
red.
(B) Determine if cross reference information is available in the cockpit to
allow elimination from consideration of any of the red segments (e.g., red low fuel
pressure light and low fuel pressure gauge). Normal operation of the gauge would be a
reason to assume the light did not cause the problem.
(C) Where a cross reference is available, further design review of that
function is not necessary; however, it may be appropriate to include procedural
information in the emergency procedures section of the rotorcraft flight manual.
(D) If cross references are not available for red segments, additional
isolation should be incorporated into the annunciator design for those functions.
(ii) If cross referencing is not practical, the following approach is
encouraged.
(A) Review the annunciator panel design and note which segments are
red.
(B) Determine if isolation diodes are checked during the application of
battery or external power before starting the engines (e.g., red low oil pressure light). If
isolation diode is shorted, all panel segments will light as soon as battery or external
power is applied.
(C) When the isolation diode can be checked before starting engines,
further design review is not necessary.
(D) If diodes are not automatically checked before starting, then additional
isolation, should be considered.
Page F - 38
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.