Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/30/99 AC 27-1B
(5) The primary test for designation of color is:
(i) Red - Is immediate action required?
(ii) Amber - Is pilot action (other than immediate) required?
(iii) Green - Is safe operation indicated, and is the indication sufficiently
distinct to prevent confusion with the landing gear down indication?
(iv) Other advisory lights - Is the meaning clear and distinct enough to
prevent confusion with other annunciations? Do the colors which are utilized differ
sufficiently from the colors specified in paragraphs b(1), (2), and (3) above?
(6) Annunciator lights should be visible during bright daylight conditions. This
should include visibility in direct sunlight unless lights are located in such a manner that
direct sunlight cannot impinge on them.
(7) If dimming capability is provided, all annunciators, including master warning
and caution, may be dimmable so long as the annunciation is clearly discernable for
night operation at the lower lighting level. Undimmed annunciations have been found
unacceptable for night operation due to disruption of cockpit vision at the high intensity.
The dimming circuit should automatically revert to the high intensity setting when power
is removed. Automatic dimming/brightening through the use of a photo cell is also
acceptable, as are circuits which enable a dimming switch through a position light or
other cockpit lighting controls.
(8) The use of flashing lights should be minimized. If a flashing feature is used,
it should be controllable through pilot action so that flashing annunciation does not
persist indefinitely. The indicator should be so designed that if it is energized and the
flasher device fails, the light will illuminate and burn steadily.
(9) The activation of caution and warning lights should readily attract the
attention of the appropriate crewmember while performing duties under both normal and
high workload conditions.
c. Annunciator Panel Design
(1) Explanation.
(i) The annunciator panel design should be reviewed for the presence of
failure modes that can cause illumination of multiple panel segments.
(ii) Many test circuits that are diode isolated are vulnerable to this
condition. A typical sequence begins with the shorting of a test circuit diode. This
failure is undetectable and goes unnoticed until an actual failure condition occurs which
Page F - 37
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.