FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page F-30.16

PDF page 606 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 606
AC 27-1B · F-30.16Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

6/23/23                                        AC 27-1B, Chg 9

            (A) Temperature Tests.


          1. Temperature tests may be accomplished by instrumenting the installed
           equipment environment with a recorder that provides a permanent record
             of time, altitude, and temperature. The pertinent temperature should be
           recorded as the rotorcraft is operated throughout its altitude range,
             including ground operation. The maximum and minimum temperatures
           recorded should be corrected degree for degree to ensure the equipment
           under test remains within its temperature rating while the rotorcraft
            operates throughout its approved ambient temperature envelope. (For
            generator or alternator cooling test procedures, refer to section 27.1351 of
              this AC.) Section 27.1043(b) requires the maximum approved operating
        OAT be at least 100° F for powerplant-mounted accessories such as
              starter generators and vacuum pumps. Due to the impracticality of the
           100° F hot day temperature limit, rotorcraft systems mounted on the
           powerplant are normally evaluated for at least 115° F hot day sea level
            conditions with corresponding 3.6° F/1,000-foot correction. The maximum
            hot day OAT at sea level must be specified in the rotorcraft flight manual
            per §§ 27.1309 and 27.1581(a)(2). Section 27.1043(b) is the regulatory
            basis for the lapse rate of 3.6° F/1,000 feet. This lapse rate should be
            applied regardless of the hot day sea level temperature the applicant
           chooses to certify for operation.

          2. The § 27.1043(b) maximum ambient temperature definition should not be
           confused with operating temperatures in closed areas. Closed equipment
            rack areas can easily reach temperatures of 140° F when sitting on the
          ramp in the southern United States in midsummer. Normally, proper
             selection of the altitude temperature category in the latest revision of DO­
          160 will ensure compliance.

          3.  In some cases, the equipment manufacturer furnishes temperature limits
              for internal critical parts (for example, brushes, bearings, or field windings
          on DC generators). In these cases, it is better to record the critical
          component temperature rather than equipment or equipment environment
            temperature.

          4. The following illustrates an acceptable high temperature evaluation
           method:


     TOAT MAX = Maximum outside air temperature at which temperature tests are
     conducted.

     TMAX = Maximum temperature to which the installed equipment has been tested
       in the laboratory.



                            Page F - 30.16

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →