FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page F-30.15

PDF page 605 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 605
AC 27-1B · F-30.15Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

6/3/23                                          AC 27-1B, Chg 9


 applicants are highly encouraged to apply DO-254 to other hardware components up to
 the LRU and systems level.

        (9) Environmental Qualification.


                 (i) Laboratory Tests.


             (A) Environmental Standards. In order to ensure that the components and
 systems under consideration will function properly when exposed to adverse
 environments, they should be tested in the laboratory under a simulated adverse
 environment. If a TSO exists and is appropriate in environmental range and
 performance for an equipment installation, it is preferable the equipment be TSO
 approved. If there is no applicable TSO or an existing TSO does not provide for a
 sufficiently adverse environment, the latest revision of RTCA DO-160 is an acceptable
 environmental standard for laboratory qualification of aircraft equipment.

             (B) Explosion Tests. Those items of electrical and electronic equipment that
 are to be located in areas subject to flammable fluids and vapors as a result of any
 single probable malfunction or failure, including failure of couplings or lines, should be
 tested as an ignition source. These tests consist of normal operation of the equipment in
 a physically contained explosive atmosphere. The explosion test procedure in the latest
 revision of DO-160 will satisfy this requirement. Section 27.863 of this AC provides
 further guidance on safety from explosion. Another standard that is equivalent to the
 latest revision of DO-160 may also be accepted to satisfy this requirement.


                  (ii) Installed Environmental Tests. After the environmental ratings of the
 components and systems have been established, it should be ensured that as installed,
 these ratings will not be exceeded. Normally, installed equipment need not be
 instrumented and tested in flight nor is it necessary to instrument the compartment or
 rack where the equipment is installed. Satisfactory environment and equipment
 compatibility are ensured by selection of the proper environmental category of
 laboratory tests. The category is determined by the type of aircraft (reciprocating or
 turbine) and flight envelope (altitude and temperature). Exceptions to normal
 installations are (a) Alternator or generator cooling, where radiated and conducted heat
 is almost always uncertain, and cooling air temperatures and flow rates are uncertain;
 (b) Where flight tests reveal excessive instrument panel vibration. In this case, the panel
 should be instrumented, tested, and, if necessary, design improvements made; and (c)
 Any other case where good engineering judgment and application of sound engineering
 principles indicate a high likelihood that the installed environment is more severe than
 the equipment is capable of operating within.





                            Page F - 30.15

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →