Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
3/31/2014 AC 27-1B, Chg 4
It can be seen that there is an acceptable margin at all altitudes up to and including
15,000 feet. However, at 20,000 feet, the margin is negative and the system fails.
(ii) Vibration tests. Normally, installed vibration tests are not necessary for
equipment qualified in accordance with the latest revision of RTCA document DO-160.
This paper categorizes vibration tests according to installed rotorcraft equipment
location such as fuselage, engine compartment, instrument panel, equipment rack, etc.
However, installed equipment vibration tests may be necessary when it appears the
equipment location environment may exceed the laboratory-tested equipment vibration
limits.
(iii) Altitude tests. If the equipment has been laboratory tested to the
maximum certified altitude of the rotorcraft, installed altitude tests are unnecessary.
The installed equipment must be either laboratory tested or tested in the rotorcraft to the
maximum certified altitude of the rotorcraft.
(3) Lightning Protection.
(i) Background. During the original design and development of rotorcraft
and the development of regulations concerning these aircraft, little attention was given
to protection from the meteorological phenomenon of lightning. This was, in part,
because the early aircraft were constructed mostly of metal and had little, if any,
dependence on advanced technology systems. Contemporary design normal category
rotorcraft are utilizing the same advanced technology systems and materials as
airplanes. Because of this fact, a specific requirement was added by Amendment 27-21
for the consideration of lightning strike protection of required systems, equipment, and
installations. The addition of paragraph (d) to § 27.1309 further defined the
consideration required for the foreseeable operating condition of a lightning strike
encounter on the rotorcraft.
(ii) Procedures.
Section 27.1309(d) requires when showing compliance to § 27.1309(a) and (b) that the
effects of lightning strikes on the rotorcraft must be considered. Guidance to show
compliance with § 27.1309(d) is available in a dedicated AC 20-136B.
(B) Detailed means of compliance should be agreed with the authorities
taking into account the effects on the rotorcraft and minimum considerations are as
follows:
(1) Any combination of analysis and testing should be agreed to by
the authority.
(2) Margins account for uncertainty in the compliance method. As
confidence in the compliance method increases, the margin can decrease. A factor of
Page F - 19
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.