Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
3/31/2014 AC 27-1B, Chg 4
At 15,000 feet:
Th mar = 295 - (294 + (46 - 42)) = -3° F
At 20,000 feet:
Th mar = 295 - (290 + (28 -20)) = -3° F
Since Th mar comes out negative at the 15,000- and 20,000-foot points, the generator
fails. It will be necessary for the applicant to reduce the maximum load current, improve
cooling, or otherwise change the design to ensure the generator is operating within its
approved temperature limit of 295° F.
(G) In most cases, the equipment is laboratory tested to minimum
temperatures as severe as that of the rotorcraft’s maximum certified altitude on a
minimum temperature day. Therefore, unless equipment minimum temperature is
affected by refrigeration or other temperature reducing environments, actual installed
instrumented minimum temperature tests are unnecessary. If low temperature
evaluation is necessary for the installed equipment, the following is an acceptable
method:
Toat min = Minimum outside air temperature at which temperature tests are
conducted.
Tmin = Minimum temperature to which the installed equipment has been
tested in the laboratory.
Ttest min = Minimum installed equipment temperature recorded during tests.
Torl = The low reference outside air temperature. It varies with altitude
starting at the lowest sea level temperature at which rotorcraft
operation is to be approved and decreases at 3.6° F/1,000-foot
altitude.
T1 mar = Temperature margin between the minimum equipment
temperature substantiated in the laboratory and the minimum
installed equipment temperature. If the margin is zero or
positive, the equipment passes. If the margin is negative, the
equipment fails the test.
T1 mar = -(Tmin - (Ttest min + (Torl - Toat min)))
Note: This equation assumes all temperatures are negative. It is necessary to place
a (-) in front of the right side of the equation in order to convert the T1 mar value
to the conventional positive answer for acceptance and a negative answer for
Page F - 17
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.