Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
3/31/2014 AC 27-1B, Chg 4
or malfunction of this cooling system. Some type of cockpit visual annunciation with the
capability to perform a preflight test is usually utilized to fulfill this requirement.
(C) Temperature tests may be accomplished by instrumenting the installed
equipment environment with a recorder that provides a permanent record of time,
altitude, and temperature. The pertinent temperature should be recorded as the
rotorcraft is operated throughout its altitude range, including ground operation. The
maximum and minimum temperatures recorded should be corrected degree for degree
to ensure the equipment under test remains within its temperature rating while the
rotorcraft operates throughout its approved ambient temperature envelope. (For
generator or alternator cooling test procedures, refer to section 27.1351 of this AC.)
Section 27.1043(b) requires the maximum approved operating OAT to be at least
100° F for powerplant-mounted accessories such as starter generators, vacuum pumps,
etc. Due to the impracticality of the 100° F hot day temperature limit, rotorcraft systems
mounted on the powerplant are normally evaluated for at least 115° F hot day sea level
conditions with corresponding 3.6° F/1,000-foot correction. The maximum hot day OAT
at sea level must be specified in the rotorcraft flight manual. Section 27.1043(b) is the
regulatory basis for the lapse rate of 3.6° F/1,000 feet. This lapse rate should be
applied regardless of the hot day sea level temperature the applicant chooses to certify
for operation.
(D) The § 27.1043(b) maximum ambient temperature definition should not
be confused with operating temperatures in closed areas. Closed equipment rack areas
can easily reach temperatures of 140° F when sitting on the ramp in the southern United
States in midsummer. Normally, proper selection of the altitude temperature category in
the latest revision of DO-160 will ensure compliance.
(E) In some cases, the equipment manufacturer furnishes temperature
limits for internal critical parts. (For example, brushes, bearings, or field windings on
DC generators.) In these cases it is better to record the critical component temperature
rather than equipment or equipment environment temperature.
(F) The following will illustrate an acceptable high temperature evaluation
method:
Toat max = Maximum outside air temperature at which temperature tests are
conducted.
Tmax = Maximum temperature to which the installed equipment has
been tested in the laboratory.
Ttest max = Maximum installed equipment temperature recorded during tests.
Torh = The high reference outside air temperature. It varies with altitude
starting at the highest sea level temperature at which rotorcraft
operation is to be approved and decreases at 3.6° F/1,000 foot
Page F - 15
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.