FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page F-8

PDF page 566 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 566
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99


                  (i)    This integration and resultant mitigation of independence can result in
an increased opportunity for common mode failures. Approval of the compensating
features is elevated in importance as it is this aspect that allows the concept to be
acceptable and subsequently certifiable. The loss of all displayed information or
erroneous information should be considered for determination of worst case criticality.
With this determination of criticality, the design can be evaluated to see that it meets the
minimum associated level of design assurance. Additionally, due to space limitations,
some systems employ “page over” features that may have some difficulty displaying the
required information when needed and human factors aspects must be considered.

                   (ii)   The instrument display system must be investigated and found to be
acceptable under both normal and emergency conditions, must perform its intended
function under foreseeable operating conditions, and must be designed to minimize the
hazards in the event of probable malfunction or failure.

                    (iii)     It must be shown that there is appropriate redundancy to provide
adequate compensation for the loss of independence in the system.  If a multi-page
system is employed, it must be shown that needed information is displayed when
required. Specific issues that must be addressed to assure compliance with the
minimum safety standards are as follows:

►The level of most severe hazard must be determined.

►Equivalent reliability and software design assurance to the determined criticality level
must be shown.

         (3) Additional sections to be consulted when determining the powerplant
instrument installation design are §§ 27.1321, Arrangement and visibility; 27.1337,
Powerplant instruments; 27.1381, Instrument lights; 27.1543, Instrument markings:
General; 27.1549, Powerplant instruments; 27.1551, Oil quantity indicator; and 27.1553,
Fuel quantity indicator.

AC 27.1305A.   § 27.1305 (Amendment 27-23) POWERPLANT INSTRUMENTS.

     a. Explanation. Amendment 27-23 revises, edits, and adds new powerplant
instrument requirements. Section 27.1305(l) was revised to require a low fuel warning
device for each tank that can be used to feed an engine. The amendment allows a
longer time between warning actuation and fuel exhaustion and requires the low fuel
warning device to be independent of the normal fuel quantity indication system.
Section 27.1305(q) was changed to extend its application to all rotorcraft (not just those
with turbine engines) and to require an indication to the crew of the degree of filter
blockage as it relates to the fuel flow requirements in § 27.955. Section 27.1305(s) was
revised to require function indicators only for fuel heaters that can be selected or are
controllable.



Page F - 8

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →