Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
2/12/03 AC 27-1B, Chg 1
relatively new technology embodied in the EFIS, the conventional technology
electromechanical standby attitude indicator, with its independent power supply, should
be retained.
c. Standby Instruments. The EFIS which have been approved on normal category
rotorcraft at this time have only presented the critical function of attitude display. A
specific requirement for a standby attitude instrument is contained in Appendix B of
Part 27. This requirement is usually satisfied by an electromechanical panel-mounted
gyro with an independent power source. Because of the mature technology of this type
of standby attitude indicator, certain aspects of the EFIS installation have not been an
area for concern. If, however, a total commitment of critical display functions is made to
the “glass” technology, such that the standby attitude instrument requirement is satisfied
by a software based CRT system, then several major areas of concern will be raised.
Among these are the electromagnetic vulnerability of the system (protection from the
effects of lightning and high energy radio frequency fields) and software. The
certifications of EFIS with an electromechanical standby attitude indicator have not
considered loss of function critical from a software aspect (reference
paragraph AC 27.1309 for a discussion of software qualification).
AC 27.1305. § 27.1305 (Amendment 27-9) POWERPLANT INSTRUMENTS.
a. Explanation. This section specifies the instruments which are required for
reciprocating and turbine engine installations. These instruments will provide the pilot
with essential data to determine operational status of critical components and select
desired performance conditions.
b. Procedures.
(1) FAR 27.1305(f), (g), and (l) requires a warning device for transmission oil
temperature, gearbox oil pressure, and low fuel. An indicator/gage is not acceptable for
use as a warning device since the indicator/gage is not a primary instrument and
therefore is not actively monitored.
(2) There are advanced display systems that take advantage of microprocessor
power by integrating the processing of several parameters. These systems have to
date been referred to as Engine Caution Advisory Systems (ECAS) or as Integrated
Instrument Display Systems (IIDS) and possibly other variations of these names. These
systems typically integrate propulsion instruments, fuel quantity indication, and caution
and warning system into a single display system. In traditional designs the powerplant
instruments, fuel quantity display, and the caution and warning system are independent
from each other. The integration of these systems/indicators eliminates their
independence from one another and increases the probability of loss of more than one
indicator/system as a result of a single fault or malfunction. Redundant design is
generally applied to compensate for the loss of independence.
Page F - 7
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.