FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page F-5

PDF page 563 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 563
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

2/12/03                                        AC 27-1B, Chg 1

                 (iv) Simulation is an invaluable tool for display evaluation. Acceptable
simulation ranges from a rudimentary bench test set up, where the display elements are
viewed statically, to full flight training simulation with motion, external visual scene, and
entire rotorcraft systems representation. For minor or simple changes to previously
approved displays, one of these levels of simulation may be deemed adequate for
display evaluation. For evaluation of display elements that relate directly to rotorcraft
control (i.e., air data, attitude, power parameters, etc.), simulation should not be relied
upon entirely. The dynamics of rotorcraft motion, coupled with the many added
distractions and sensory demands made upon the pilot that are attendant to actual
helicopter flight, have a profound effect on the pilot’s perception and usability of
displays. Display designers, as well as FAA/AUTHORITY test pilots, should be aware
that display formats evaluated and found acceptable in simulation may well (and
frequently do) turn out to be unacceptable in actual flight.

               (v)  Prior to defining the characteristics (color, symbology, etc.) or
standards to be used on a specific display, a flight deck design philosophy should be
established. Additionally, displays should be consistent across all systems in the flight
deck. Documentation of the usage for display philosophy would help establish the
working basis for determining compliance.

               (2) Symbology and Function.

                    (i) When assessing the acceptability of the EFIS, consideration should
be given to the effect of the loss of one of the CRT color guns. This type of failure is
especially a factor in determining the acceptability of the installation for single-pilot
operation.

                      (ii) Symbols should be distinctive to minimize misinterpretation or
confusion with other symbols utilized in the displays. The type and function of
symbology should be clearly defined and appropriately classified for pilot understanding.
Symbols representing the same functions on more than one display should utilize the
same shape and/or color-coding.

               (3) Display Chromaticity and Luminance. The chromaticity and
luminance of the displays should be determined to be acceptable for all cockpit lighting
conditions which are expected in service. An expanded discussion of these
characteristics may be found in AC 25-11 and AC 23.1311.

               (4) Temperature Survey to Determine Proper Cooling of EFIS
Components.

                    (i)  Equipment Requiring Cooling Test. As with any avionic equipment,
good engineering judgment may deem that all components of the EFIS should have an
in-flight temperature survey performed to ascertain that the thermal environmental
tolerance of the system components is not exceeded. Usually, the following general



                                                        Page F - 5

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →