Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 1 2/12/03
(a) Reasonable training times and learning curves; (however, realistic
assumptions should be made concerning the actual time for an average pilot to
learn/adapt to a system. Also, these assumptions should reflect the fact that Part 91
pilots might not be trained, since training is not typically required.);
(b) Usability in an operational environment;
(c) Acceptable interpretation error rates equivalent to or less than
conventional displays;
(d) Proper integration with other equipment that uses electronic display
functions;
(e) Acceptability of all failure modes including those failures or
combinations of failures not shown to be extremely improbable; and
(f) Compatibility with other displays and controls.
The manufacturers should provide human factors support/rationale for their decisions
regarding new or unique features in their EFIS display. Evaluation pilots should verify
that the data supports a conclusion that any new or unique features have no human
factors traps or pitfalls, such as display perceptual or interpretive problems, for a
representative pilot population.
(ii) It is desirable to have display evaluations conducted by more than one
pilot, even for certification of EFIS displays that do not incorporate significant new
features. For display designs that incorporate unproven features, evaluation by a
greater number of pilots should be considered. To help the FAA/AUTHORITY
certification team gain assurance of a sufficiently broad exposure base, the electronic
display manufacturer or installer should develop a test program with the certificating
office that gathers data from FAA/AUTHORITY test pilots, company test pilots, and
customer pilots who will use the display. A reasonable amount of time for the pilot to
adapt to a display feature can be allowed, but long adaptation times must receive
careful consideration. Any attitude display format presented for FAA/AUTHORITY
approval should be sufficiently intuitive in its design so that no training is required for
basic manual rotorcraft control.
(iii) For those electronic display systems that have been previously
approved (including display formats) and are to be installed in rotorcraft in which these
systems have not been previously approved, a routine FAA/AUTHORITY certification
review should be conducted. This program should emphasize the systems’ integration
in the rotorcraft, taking into account the operational aspects, which may require further
detailed systems failure analysis (where “system” means display, driving electronics,
sensors, and sources of information).
Page F - 4
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.