FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page F-3

PDF page 561 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 561
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

2/12/03                                        AC 27-1B, Chg 1

regard to color, symbology, operation, and so forth. This paragraph along with some
others in this document principally highlights the areas that are peculiar to the
installation in a normal category rotorcraft. A discussion of the flight director function
performed by the EFIS is given in paragraph AC 27.1335. A discussion of the location
of the displays is contained in paragraph AC 27.1321. A discussion of the
recommendations for an EFIS is contained in the latest versions of both AC 25-11,
Transport Category Airplane Electronic Display Systems and AMJ 25-11, Electronic
Display Systems, and refer to AC-23.1311-1A, Installation of Electronic Displays in Part
23 Small Airplanes, dated March 12, 1999.

                   (ii)   Procedures.

              (A) System Components. The system components require qualification
testing to determine that their design is acceptable, free from hazards, and suitable to
their airborne environment. The components of the EFIS should meet the requirements
of TSO C-113, C2d, C3d, C4c, C5e, C6d, and C10b (other TSOs for EFIS may apply).

               (1) Environmental Qualification. The EFIS hardware must be shown to
be suitable to its airborne environment. A desirable way to qualify the system
component is to obtain approval to the appropriate TSO.  If the equipment is not TSO
approved, it should be shown via testing that it complies with the requirements of SAE
Document AS-8034, the latest revision of RTCA Document DO-160, and other
appropriate standards. This may include testing in accordance with the appropriate
categories of the latest revision of RTCA Document DO-160, JEDEC Publication
No. 64D (Protection from Ionizing Radiation), and UL Document No. 1418 (Impact
Implosion Test).

               (2) Software. The embedded software should be qualified in accordance
with the latest revision of RTCA Document DO-178B. The software level is contingent
on the worst case criticality of the function it performs. The software should be
designed to provide adequate consideration for this factor (reference
paragraph AC 27.1309). A similar consideration is required for altitude and airspeed.

              (B) System Installation Considerations.

               (1) Human Factors. Humans are very adaptable, but they adapt at
varying rates with varying degrees of effectiveness and mental processing
compensation. Thus, what some pilots might find acceptable and approvable, others
would reject as being unusable and unsafe. Rotorcraft EFIS displays must be effective
when used by pilots who cover the entire spectrum of variability. Relying on a
requirement of “train to proficiency” may be unforeseeable, economically impracticable,
or unachievable by some pilots without excessive mental workload as compensation.

                    (i)  In order to minimize the potential for changes to first time EFIS
installation approvals, the test program for EFIS displays should include sufficient flight
and simulation time, using a representative population of pilots, to substantiate:


                                                        Page F - 3

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →