FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-137

PDF page 557 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 557
AC 27-1B · E-137Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

type which senses flame within a visible space. Overheat-fire detectors can be
obtained in either “continuous” or “unit” type.

         (4) The detector system should:

                  (i)    Indicate fire within 15 seconds after ignition, and show in which engine
compartment the fire is located.

                   (ii)   Remain on for the duration of the fire.

                    (iii)   Indicate when the fire is out.

               (iv)   Indicate re-ignition of the fire.

              (v)   Not by itself precipitate or add to the potential of any other hazards.

               (vi)  Not cause false warnings under any flight or ground operating
condition.

         (5) Additional features of the detection system are as follows:

                  (i)   A means should be incorporated so that operation of the system can
be tested from the cockpit.

                   (ii)   Detector units should be of rugged construction, to resist maintenance
handling, exposure to fuel, oil, dirt, water, cleaning agent, extreme temperatures,
vibration, salt air, fungus, and altitude. Also, they should be light in weight, small, and
compact, and readily adaptable to desired positions of mounting.

                    (iii)  The detector system should operate on the rotorcraft electric system
without inverters. The circuit should require minimum current unless indicating a fire or
unless a monitoring system is in use.

               (iv)  Fixed temperature fire detectors should preferably be set at 100° F
(37.7° C) to 150° F (65.6° C) above maximum safe ambient temperature, or higher
when in compartments where extremely high rate of rise is normally encountered.

              (v)   Detector system components located within fire zones should be
fireproof.

               (vi)  Each detector system should actuate a warning device which
indicates the location of the fire.  If fire warning lights are used, they must be in the
pilot’s normal field of view.

                (vii)  Two or more engines should not be dependent upon any one detector
circuit. The installation of common zone detection equipment prevents the detection


                                                      Page E - 137

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →