Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
of the pilot. In such cases, psychology should be weighted against complexity, and
“panic switches,” combining multiple procedure functions, should be provided to simplify
the mental demands on the pilot. Speed is gained by such designs for hazards which
may need it.
(iii) The detector of an automatic system automatically triggers the
appropriate countermeasures and warns the pilot simultaneously. Such a system
should be carefully evaluated to assure that the advantages outweigh the
disadvantages and potential malfunctions.
(2) Fires, or dangerous fire conditions can be detected by means of various
existing techniques. The following is a partial list of available detectors:
(i) Radiation-sensing detectors.
(ii) Rate-of-temperature-rise detectors.
(iii) Overheat detectors.
(iv) Smoke detectors.
(v) CO detectors.
(vi) Combustible mixture detectors.
(vii) Fibre-optic detectors.
(viii) Ultraviolet.
(ix) Observation of crew or passengers.
(3) In many rotorcraft it is desirable to have a detection system which
incorporates several of these different types of detectors. Radiation-sensing detectors
are most useful where the materials present will burn brightly soon after ignition, such
as in the powerplant accessory section. Rate of rise detectors are well-suited to
compartments of normally low ambient temperatures and low rates of temperature rise
where a fire would produce a high temperature differential and rapid temperature rise. It
should be noted that under certain circumstances, where a relatively slow temperature
increase occurs over a considerable period of time, a fire can occur without detection by
rate of rise detectors. Overheat detectors should be used wherever the hazard is
evidenced by temperatures exceeding a predicted, set value. Smoke detectors may be
suited to low air flow areas where materials may burn slowly, or smolder. Fibre-optic
detectors can be used to visually observe the existence of flame or smoke. The three
major detector types used for fast detection of fires are the radiation-sensing,
rate-of-rise, and overheat detectors. Radiation-sensing detectors are basically “volume”
Page E - 136
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.