FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-135

PDF page 555 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 555
AC 27-1B · E-135Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

using the definition of a severe fire and of the resultant “other surface” temperature
based on a single fire occurring in each engine compartment and designated fire zone,
on a case-by-case basis. Once the other surfaces are identified and their severe fire
induced maximum temperatures determined, their configuration and material selection
should be reviewed on a case-by-case basis to determine either that they are fire
resistant, that they can be made fire resistant (within the limits of practicability), or that it
is impracticable to make them fire resistant.  If the non-fire resistant other surfaces can
be readily made fire resistant they should be.  If it is impracticable to make them fire
resistant, then they should be relocated, insulated, or a combination in order to reduce
the total incident heat flux (and, thus, lower their surface temperature) so that they no
longer need be fire resistant.  If insulation is used to shield a surface that is subjected to
a significant temperature, it must be fire resistant.

         (2) A partial validation of analytical heat flux models using the definition of a
severe fire can sometimes be achieved during certification tests by using thermocouples
or heat-sensitive stickers to measure in-flight temperature ranges and distributions on
other surfaces from known thermal environments in engine compartments or other
designated fire zones.

AC 27.1195.    § 27.1195 (Amendment 27-5) FIRE DETECTOR SYSTEMS.

     a. Explanation.

         (1) This section requires quick-acting fire detectors to be installed on turbine
powered rotorcraft, when the engine compartment cannot be readily observed in flight
by the pilot in the cockpit.

         (2) The number of detectors and locations must be sufficient to ensure prompt
detection of fire in the engine compartment.

     b. Procedures.

         (1) The detector system should be designed for highest reliability to detect a
fire and not to give a false alarm.  It is desirable that it only responds to a fire and
misinterpretation with a lesser hazard should not be possible. Engine overtemperature,
harmless exhaust leakage, and bleed air leakage should not be indicated by a fire
detector system. A fire detection system should be reserved for a condition requiring
immediate measures such as engine shutdown or fire extinguishing. There are three
general types of detector-procedure systems that are commonly used:

                  (i)   A manual system utilizes warning lights to alert the pilot who then
follows prescribed cockpit procedure as a countermeasure. A manual system is
adequate for hazards in which a few seconds are not important.

                   (ii)   There is also a semi-automatic system. Occasionally a rotorcraft
becomes so complex that the emergency procedure exceeds reasonable expectations


                                                      Page E - 135

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →