Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
(3) The failure of one latching device should not cause the failure of another
latching device. If a failure of a single retention device can contribute to multiple
failures, these multiple failures should be considered.
(4) The consequences of “forgetting” to latch a cowl should be considered.
(5) The use of safety straps should be considered to minimize the impact of a
latching device failure.
AC 27.1194. § 27.1194 (Amendment 27-2) OTHER SURFACES.
a. Explanation. This section states the fire resistance requirements for material
surfaces near engine compartments and designated fire zones (other than tail surfaces
not subject to heat, flames or sparks emanating from a designated fire zone or engine
compartment).
b. Definition.
(1) Other Surface. Any airframe, system, or powerplant component aft of and
near an engine compartment, a designated fire zone, or another heat source which
would receive a heat flux as a result of a fire in the engine compartment or fire zone that
would require the component to be fire resistant.
(2) Fire Resistant. In accordance with § 1.1, is defined as follows:
(i) Sheet metal or structural members with the capacity to withstand the
heat associated with the fire at least as well as aluminum alloy in dimensions
appropriate for the purpose for which they are used.
(ii) Fluid carrying lines, fluid system parts, wiring, air ducts, fittings and
powerplant controls with the capacity to perform their intended functions under the heat
and other conditions resulting from a fire.
(3) Fire. A fire in either an engine compartment or a designated fire zone is
assumed to occur that produces a heat flux on a system, airframe or powerplant
component aft of or near the fire. The effect of each such fire on other surfaces must be
considered on a case-by-case basis to determine the critical case. Unless a more
rationale definition is furnished and approved during certification, the fire in any engine
compartment or designated fire zone should be assumed, for purposes of analysis, to
be a severe fire (see definition in paragraph AC 27.859).
c. Procedures.
(1) Other surfaces should be identified during certification by a design review
and by a conservative, thorough hazard analysis based on an analytical estimate of the
total heat flux (i.e., conduction, convection, and radiation in combination, as applicable)
Page E - 134
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.