FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-133

PDF page 553 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 553
AC 27-1B · E-133Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B


     b. Procedures.

         (1) Compliance with § 27.1193(a) can be shown by analyzing the cowling and
engine compartment covering and determining that no structural degradation will occur
under the highest loads experienced on the ground or in flight.

         (2) Compliance with § 27.1193(b) can be accomplished by ensuring that the
drain will discharge positively with no traps and is a minimum of 0.25 inches in diameter.

         (3) Compliance with § 27.1193(c) can be demonstrated by colored liquid
flowing through the drain system while in flight. The dye should not impinge on any
ignition source during any approved flight regime.

         (4) Compliance with § 27.1193(d) can be accomplished by showing that the
cowling and engine compartment covering is fire resistant. Fire resistant in this context
means a material that has the capacity, under expected service conditions (load,
vibration, airflow), to withstand the heat associated with fire at least as well as aluminum
alloy in dimensions appropriate for the purpose.

         (5) Compliance with § 27.1193(e) can be accomplished by showing that the
cowling and engine compartment coverings retain adequate structural integrity when
subjected to elevated temperatures that may be expected in service.

AC 27.1193A.   § 27.1193 (Amendment 27-23) COWLING AND ENGINE
           COMPARTMENT COVERING.

     a. Explanation. Amendment 27-23 adds a new § 27.1193(f) that requires
redundant retention means for each panel, cowling, engine, or rotor drive system
covering that can be opened or readily removed. Conventional fasteners for these
devices are subject to frequent operation by maintenance personnel and have
deteriorated, failed from wear or vibration, or been left unsecured after preflight
inspections. Such a failure could be hazardous if a loose panel, cowling, or covering
comes in contact with the rotors or critical controls.

     b. Procedures. All of the policy material pertaining to this section remains in effect
with the following additions:

         (1) Compliance with § 27.1193(f) can be accomplished by simulating, or
actually failing, one or more of the retention devices or by structural analysis.  It should
be shown that the cowling or cover will not open, strike, or be struck by the rotor or
other critical component.

         (2) Consideration should be given to minimize the possibility of latches being
improperly closed that could result in a cowl coming open in flight.



                                                      Page E - 133

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →