FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-138

PDF page 558 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 558
AC 27-1B · E-138Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

system from distinguishing between the engine installations, necessitating shutting
down more than one engine.

         (6) The sensing portion of the fire detection system should not extend outside
of the coverage area into another fire zone. Detectors, with the exception of
radiation-sensing detectors, should be located at points where the ventilation air leaves
compartments.  If a reverse-flow cooling system is used, detectors should be installed at
locations which are outlets under both flight and ground operating conditions. Stagnant
air spaces should be avoided and the number of ventilation air exits should be kept to a
minimum. Compliance with these recommendations allow the effective placement of a
minimum amount of detectors, and still ensure prompt detection of fire in those zones.
Radiation-sensing detectors should be located such that any flame within the
compartment is immediately sensed. This may or may not be where the ventilation air
leaves the compartment.

         (7) Fire detectors should be installed in designated fire zones, the combustor,
turbine, and tailpipe sections of turbine installations.

                  (i)   Engine Power Section (Combustor, Turbine, and Tailpipe): This zone
is usually characterized by predictable hazard areas which facilitate proper detector
location.  It is recommended that coverage be provided for any ventilating air outlet as
well as intermediate stations where leaking combustibles may be expected.

                   (ii)   Compressor Compartment: This is usually a zone of relatively low air
flow velocities, but wide geographical possibility for fires. When fire detectors other than
radiation-sensing detectors are used, detection at air outlets provides the best
protection, and intermediate detector locations are of value only when specific hazards
are anticipated.

                    (iii)  Accessory Bullet Nose: Where such a compartment is so equipped
that it is a possible fire zone, its narrow confines permit sufficient coverage with one or
more detectors at the outlets.

               (iv)  Heater Detector Location: An overheat detector should be placed in
the hot air duct downstream of the heater.  If the heater fuel system or exhaust system
configuration is such that it is a fire hazard, the compartment surrounding the heater
should also be examined as a possible fire zone.

              (v)   Auxiliary Power Unit Detector Location: The use of a
combustion-driven auxiliary power unit creates another set of typical engine
compartments defined and treated as above. Some units are so shrouded with fireproof
material that these compartments exist only within the confines of the shroud. They are
still, however, fire zones and should have a detection system.





Page E - 138

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →