FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-131

PDF page 551 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 551
AC 27-1B · E-131Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

                       FIGURE AC 27.1191-1
            TABLE OF MATERIALS AND GAGES ACCEPTABLE
          FOR FIREPROOF PROTECTIVE DEVICES WITH FLAT
                   SURFACE GEOMETRIES(1)

             MATERIAL(2)            MINIMUM THICKNESS(3)

           Titanium Sheet                         .016 in

            Stainless Steel                          .015 in

            Mild Carbon Steel                       .018 in

          Terne Plate                             .018 in

          Monel Metal                            .018 in

            Firewall Fittings                        .018 in(4)
             (Steel or Copper Base)

NOTES:

(1)  Assumes essentially flat vertical or horizontal surfaces undergoing a uniform heat
flux. Any significant variation in either geometry or heat flux distribution should be
examined in detail for adequate gauge thicknesses on a case-by-case basis.

(2)  Must have corrosion protection if not inherent in the material itself.

(3)  The minimum thickness is for thermal containment only. Structural integrity
considerations may require thickness increases. MIL-HDBK-5D contains material
allowable versus temperature data for most common metallic materials.

(4)  This is the minimum wall thickness measured at the smallest dimension (e.g.,
thread root or other location) of the part.

(5)   Distortion of thin sheet materials and the subsequent gapping at lap joints or
between rivets is difficult to predict; therefore, testing of the simulated installation is
necessary to prove the integrity of the design. However, rivet pitches of 2 inches or less
on non load-carrying titanium firewalls of .020 inch or steel firewalls of .018 inch are
acceptable without further testing.





                                                      Page E - 131

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →