Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
combustion heaters, and combustion devices are required by regulation to be isolated.
Other high temperature devices may also require isolation because of local hot spots
(which occur during normal operations or from failure modes) that can thermally injure
occupants or cause spontaneous combustion of surroundings. A hazard analysis
should identify these potential problems and provide proper certification solutions.
(2) Fireproof protective devices should be able to withstand at least
2000 ± 150° F for at least 15 minutes (reference AC 20-135). The fireproof protective
device should allow protected parts, subsystems or systems to perform their intended
function for the duration of a severe fire (see definitions). For firewalls, examples of flat,
geometry materials undergoing uniform heat fluxes with material gauges that
automatically meet the certification requirements are given in figure AC 27.1191–1. If
firewalls are utilized that involve other materials, significant geometric changes, or
significantly non-uniform heat fluxes, then automatic compliance may not be assured.
In such cases the fireproof protective device should be analyzed using the severe fire
definition and, in some cases, tested in accordance with AC 23–2 to ensure proper
certification. For example, a curved protective surface may absorb a uniform incident
heat flux unevenly and create a local hot spot that exceeds 2,150° degrees Fahrenheit
that burns through in less than 15 minutes; whereas, a flat surface of equal thickness
might not exceed 2,150°degrees Fahrenheit and would not burn through in less than
15 minutes. It should be noted that composite materials are not generally used for
protective devices because of their inability to withstand high temperatures (i.e.,
exceedance of the glass transition temperature); however, some specially formulated
composites have been previously certified as engine cowlings. Titanium is an
acceptable material for fireproof protective devices such as firewalls. However, use of
titanium should always be carefully considered and reviewed, because it can lose all
structural ability and burn severely (self combust) above 1,050° F, under certain
thermodynamic environments, and contribute to the fire instead of providing the
intended fire protection. AC 33–4, “Design Considerations Concerning the Use of
Titanium in Aircraft Turbine Engines” and MIL-HDBK-5D contain more detailed
information on the unique thermal properties of titanium.
Page E - 130
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.