FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-129

PDF page 549 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 549
AC 27-1B · E-129Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

fuel, fumes and potential ignition sources (i.e., “potential hazards”). Each fireproof
protective device must, by regulation, meet the following criteria:

         (1) Its design and location must take into account the probable fire path from
each fire zone or source considering factors such as internal airflow, external airflow,
and gravity.

         (2) It must be constructed so that no hazardous quantity of air, fumes, fluids, or
flame can propagate through it to unprotected parts of the rotorcraft.

         (3) Its openings (e.g., shaftholes, lineholes, etc.) must be sealed with close
fitting fireproof grommets, bushings, bearings, firewall, fittings, or equivalent that prevent
burn through and leakage of hazardous fumes or fluids from the fire zone.

         (4) It must be fireproof (see definition).

         (5) It must be either corrosion resistant or otherwise safely protected from
corrosion.

     b.  Definitions.

         (1) Fireproof Protective Device. A fireproof protective device is a device such
as a firewall, shroud, enclosure, or equivalent used to isolate a heat or potential fire
source (severe fire) from personnel compartments and from critical aircraft components
which are essential for a controlled landing.

         (2) Fireproof. Fireproof is defined in § 1.1 “General Definitions.”

         (3) Controlled Landing. A landing which is survivable (i.e., does not fatally
injure all occupants) but may produce an unairworthy, partially salvageable, or
unsalvageable rotorcraft.

         (4) Severe Fire. See Definition in paragraph AC 27.859.

      c. Procedures. Fireproof protective devices are typically certified by analysis,
tests, or a combination conducted during the certification process, including flight tests
or simulated flight tests, as follows:

         (1) Fireproof protective devices should be provided wherever a hazard exists
which requires isolation from a severe fire to avoid fires in personnel compartments and
to avoid thermal damage to critical components (such as structural elements, controls,
rotor mechanisms, and system components) that are necessary for a controlled landing.
A thorough hazard analysis should be conducted during certification to identify, define
and quantify in order of severity (i.e., maximum temperature, hot exposed area, etc.) all
thermal hazards or zones that require fireproof protection in a given design. Engines
(including the combustor, turbine, and tailpipe sections of turbine engines), APU’s,


                                                      Page E - 129

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →