FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-125

PDF page 545 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 545
AC 27-1B · E-125Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

AC 27.1185.    § 27.1185 (Amendment 27-11) FLAMMABLE FLUIDS.

     a. Explanation. This section requires that fuel, flammable fluid, or vapor tanks,
reservoirs or collectors be sufficiently isolated from engines, engine compartments, and
other designated fire zones so that hazardous heat transfer from these areas to fuel,
flammable fluid, and vapor tanks, reservoirs, or collectors is prevented in either normal
or emergency service.

     b.  Definitions.

         (1) Fuel or Flammable Fluid Collector. Any device such as a large valve,
accumulator, or pump that contains a significant amount of flammable fluid, fuel, or
vapor (e.g., the volume equal to 10 ounces or more of fluid).

         (2) Flammable Fluid or Vapor Tank. Any fuel, flammable, fluid, or vapor tank,
reservoir, or collector.

         (3) Sufficiently Isolated. Fuel, flammable fluids, or vapors in a tank, reservoir,
or collector are insulated, removed, otherwise protected or a combination such that their
worst case temperatures (the worst case measured or calculated surface temperature
of their containers) in either normal or emergency service is always 50° F or more away
from the autoignition temperature of the fuel, flammable fluid, or vapor in question.

         (4) Minimum Autoignition Temperature. The temperature at a given vapor
pressure at or above which liquid fuel or fuel vapor will self combust. When determining
the minimum design value of autoignition temperature which will occur in either normal
or emergency operations, the critical, in-service combination of vapor pressure and fuel
temperature should be determined.

         (5) Hazardous Heat Transfer. A total incident heat flux (a combination of
conduction, convection, and radiation, as applicable) from or in an engine compartment
or other designated fire zone, which would raise the temperature level of a flammable
fluid or fuel, their vapors, or the surface temperature of their containers to within 50° F
or less of the minimum in-service autoignition temperature. Typically, the most critical
heat transfer case to be considered is emergency service where a severe fire (see
definition) is assumed to occur in each engine compartment and each designated fire
zone on a case-by-case basis.

         (6) Severe Fire. See definition in paragraph AC 27.859.

      c. Procedures.

         (1) The fuel, flammable fluid, and vapor system designs should be reviewed
early in certification to insure that all flammable fluid or vapor tanks are properly
identified and isolated from engines, engine compartments, and other designated fire
zones during both normal and emergency operations such as in-flight engine


                                                      Page E - 125

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →