Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
(4) Compliance with § 27.1141(d) can be accomplished by performing a failure
mode and effects analysis (FMEA) to determine that no single failure or malfunction will
cause failure of any powerplant control function necessary for safety. Included in this
FMEA should be calculations showing the likelihood of any combination of failures of
the powerplant control systems that would cause failure of any powerplant function
necessary for safety is improbable. One acceptable procedure for documenting the
analysis is contained in Society of Automotive Engineers (SAE) Fault/Failure Analysis
Procedure ARP 926A, revised November 15, 1979.
AC 27.1141A. § 27.1141 (Amendment 27-23) POWERPLANT CONTROLS:
GENERAL.
a. Explanation. Amendment 27-23 changed § 27.1141(c) to extend its
applicability to any powerplant valve regardless of the location of the valve control. The
previous rule was only applicable for valves in the cockpit. Valves are excluded if their
function is not required for safety.
b. Procedures. This rule change did not change the suggested methods of
compliance.
AC 27.1143. § 27.1143 (Amendment 27-11) ENGINE CONTROLS.
a. Explanation. This regulation describes the arrangement and operation of the
engine controls.
(1) Each throttle mechanism should be independent of the throttles for other
engines.
(2) The arrangement of the independent throttles should allow simultaneous
control of all engines with one hand.
(3) Immediate actuation at the engine control should be provided by any given
input at the throttle control in the cockpit.
(4) If throttle controls incorporate a fuel shut-off feature, a means should be
provided to prevent inadvertent movement to the shut-off position. This means should-
(i) Provide a positive lock or stop at the idle position. An idle detent
(mechanical or electrical/mechanical such as solenoid) is an accepted arrangement.
(ii) Require a separate and distinct operation to place the control in the
shut-off position. Separate action (switch or button) to displace the idle stop or distinct
offsets in throttle motion to allow movement from the idle stop to shutoff are accepted
arrangements.
b. Procedures. None.
Page E - 118
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.