Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/30/99 AC 27-1B
SUBPART E - POWERPLANT
POWERPLANT CONTROLS AND ACCESSORIES
AC 27.1141. § 27.1141 (Amendment 27-12) POWERPLANT CONTROLS:
GENERAL.
a. Explanation.
(1) Section 27.1141(a) references §§ 27.777 and 27.1555. The detailed
compliance procedures for powerplant controls arrangement and markings are found in
these sections.
(2) Each flexible powerplant control should be approved.
(3) In order to prevent power failure due to improper powerplant control valve
positioning, § 27.1141(c) specifies acceptable open/closed positions for manual valves.
Power-assisted valves should have means to indicate to the flightcrew that the valve is
either in the fully open or fully closed position or that the valve is moving between these
two positions.
(4) For turbine installations, no single failure or malfunction, or probable
combination thereof, of any powerplant control system should cause the failure of any
powerplant function necessary for safety.
b. Procedures.
(1) Procedures for § 27.1141(a) are contained in detail in §§ 27.777 and
27.1555.
(2) Compliance with § 27.1141(b) may be accomplished by qualifying the
control to Mil-C-7958, “Controls, Push-Pull, Flexible, and Rigid,” or other approved
standards.
(3) Compliance with § 27.1141(c)(1) may be accomplished by installing manual
valves which have positive stops in the full open and closed positions. The fuel valves,
however, may have an arrangement to facilitate the capability of switching to different
fuel tanks if suitable indexing is provided. Compliance with paragraph (c)(2) may be
accomplished by installing a device which displays to the flightcrew one indication with
valve fully open and another with the valve fully closed. Alternatively, an indication
could be given when the valve is moving from fully open to fully closed with the
indication ceasing when the valve position corresponds to the selected switch position
(open or closed). An example would be a light that is off when the valve is fully open or
closed and illuminates while the valve is transitioning.
Page E - 117
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.