FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-115

PDF page 535 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 535
AC 27-1B · E-115Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

design should be performed and validated during certification. Advisory Circular
(AC) 43-4, “Corrosion Control for Aircraft” contains a detailed discussion of exhaust gas
corrosion problems. Analysis and/or verification tests of the exhaust system should be
conducted. This work is necessary to ensure thermal and structural integrity; to ensure
that thermal expansion does not cause a structural overload or failure; and, to ensure
that exhaust piping does not contact (or come close to) ambient temperature materials
(such as structure or system components). Hot exhaust piping in contact with (or close
to) ambient temperature materials can either create a fire hazard or cause an
unintended strength reduction. To ensure that thermal expansion analyses and tests
are properly conducted, the maximum in-service temperature excursion should be
properly defined. The maximum temperature excursion should be based on the
maximum temperatures of the piping and exhaust gases, as affected by the insulatory
characteristics of the piping’s enclosure, and as affected by a worst case hot day. The
worst case temperature environment used for analysis can be verified by a temperature
survey.  If run on cooler days, the survey can be adjusted for the worst case hot day
environment using methods identical to those used for engine cooling tests (reference
paragraph AC 27.1043, Cooling Tests). The piping should be designed to expand freely
so that thermal expansion (thermal strain) induced loads on the piping and its restraint
system are minimized.  If thermal expansion induced loads (in conjunction with
deflection induced loads and exhaust flow loads, discussed in b(4)) are significant
relative to the limit load of any item in the load path, then a fatigue check on the critical
design point(s) should be performed. The fatigue check should establish a safe life or
an approved limited life for the critical component(s) in the system. An accurate
analytical fatigue check on exhaust piping may be difficult to perform because of
in-service erosion, corrosion, etc.; therefore, phased inspections should be considered
to ensure the continued airworthiness of the exhaust piping.

         (2) For compliance with § 27.1123(b), exhaust piping should be properly
supported so that the maximum loads anticipated in-service are properly distributed and
reacted, and as previously discussed, so that thermal expansion induced loading is
minimized. Typically the worst case static design load conditions are either the inertia
loads from an emergency impact (reference § 27.561) or the combined loading from
thermal expansion, in-flight deflections and internal exhaust gas flow (see
paragraph b(4)).  It should be noted that several combinations of these loads should be
examined to determine the critical combination. The piping should be supported and
restrained such that critical frequencies are avoided and the induced vibration
environment’s effect is minimized. Flight test vibration surveys may be necessary, in
some cases, to properly define or validate the critical modes and environment and their
effect on the exhaust piping design. Operating modes such as ground idle, flight idle,
40 percent and 80 percent of maximum continuous power, maximum continuous power,
OEI power settings and other power settings should be investigated to determine their
vibratory effect on the exhaust gas piping system. The strength reduction of the piping
materials at operating temperature (and at worst case temperature) should be properly
considered in the design and structural substantiation. MIL-HDBK-5D contains material
allowables versus temperature data for a wide variety of metallic engineering materials.



                                                      Page E - 115

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →