FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-114

PDF page 534 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 534
AC 27-1B · E-114Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

night. One method of compliance would be a night flight evaluation at critical azimuths
and variable wind conditions to verify that no degradation exists.

         (6) Compliance with § 27.1121(f) can be accomplished by ensuring that the
drain will discharge positively and is a minimum of 0.25 inches in diameter. No drain
may discharge where it might cause a fire hazard. This can be demonstrated by
discharging a colored liquid through the drain system in flight and on the ground. The
dye should not impinge on any ignition source.

         (7) Section 27.1121(g) is self-explanatory in specifying that a means must be
provided to prevent blockage of the exhaust port after any internal heat exchanger
failure. Compliance can be shown by demonstration or by analysis. In either case, it
must be shown that any internal failure will not result in a significant power loss from the
engine.

AC 27.1123.    § 27.1123 (Amendment 27-11) EXHAUST PIPING.

     a. Explanation. This section contains the following requirements that must be met
for proper certification of exhaust piping on engines, auxiliary propulsion units (APU),
and other similar devices.

         (1) Section 27.1123(a) requires that the piping be heat and corrosion resistant
so that it performs its intended function during its operational life (either the life of the
rotorcraft or a specified limited life) without significant metal corrosion, metal erosion, or
creation of hazardous hot spots. The piping system should be designed, have an
installation design, or a combination that allows performance of its function without
thermal expansion (thermal strain) induced structural failures such as ruptures caused
by operating temperature excursions and overpressurization during its operational life.

         (2) Section 27.1123(b) requires that the piping be supported to withstand the
vibration and loading environment (including inertia loads) to which it will be subjected in
service.

         (3) Section 27.1123(c) requires that piping that connects to components
between which relative motion exists in service must have the necessary flexibility and
structural integrity to withstand the relative motion without exceeding limit load (at the
maximum operating temperature) of the piping, or creating unintended loads (or load
paths) on the components to which the piping connects.

     b. Procedures. Exhaust piping is typically certified by analysis and installation
tests conducted during the basic certification process, including flight tests, as follows:

         (1) For compliance with § 27.1123(a), because of its durability in the hot
exhaust environment, exhaust piping is typically made from stainless steel or alloy steel
of the appropriate structurally and thermally derived wall thickness. Hot aircraft exhaust
gases are very corrosive; thus, proper material selection and corrosion protective


Page E - 114

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →