FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-113

PDF page 533 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 533
AC 27-1B · E-113Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

                  SUBPART E - POWERPLANT

                      EXHAUST SYSTEM


AC 27.1121.    § 27.1121 (Amendment 27-12) EXHAUST SYSTEM--GENERAL.

     a. Explanation.

         (1) This section addresses the arrangement of exhaust components and the
protection against hazardous conditions which exist with hot exhaust gases.

         (2) The objective is to allow for thermal expansion of manifolds and pipes,
prevent local hot spots, and eliminate the possibility of igniting flammable fluids or
vapors.

     b. Procedures.

         (1) Sufficient clearance of hot exhaust components must be maintained from
structure, fuel cells, flammable fluid lines, and electrical components to compensate for
thermal growth under normal and most extreme operating temperatures. Verify that
adequate clearance exists between the exhaust system components and the
surrounding structure, and that no interference occurs under the most adverse
temperature excursions.

         (2) Hot spots that can occur on fuselage or rotor blade skin as a result of
impingement or in compartments due to an accumulation of hot gases should be
eliminated with deflectors or by providing adequate flow-through ventilation.
Compliance may be shown by demonstration or analysis.

         (3) It should not be possible to ingest sufficient quantities of exhaust gases
which will produce engine surges, stalls, or flameouts during normal and emergency
operation within the range of operating limitations of the aircraft and of the engine.
Analysis and/or flight testing may be required to demonstrate compliance.  If flight
testing is required, particular attention should be placed upon critical azimuths and wind
conditions.

         (4) Exhaust system surfaces hot enough to ignite flammable fluids or vapors
must meet the isolation or shielding requirements of this section in addition to the
requirements of §§ 27.1183 and 27.1185. Good design practice suggests that the
isolation and shielding features incorporated would continue to be effective under the
emergency landing conditions specified in § 27.561.

         (5) It should be demonstrated that exhaust gases are discharged in such a
manner that they do not cause distortion or glare which seriously affects pilot visibility at



                                                      Page E - 113

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →