Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 4 3/31/2014
d. Turbine Engines - Ground Icing.
(1) Explanation. This requirement addresses the situation where extended
ground operation in icing exposes the rotorcraft and its engine inlet to icing (ground fog)
conditions which may have different droplet impingement patterns and involve different
or less effective means of ice protection. Note that the requirement is effective in
Amendment 10 and is applicable regardless of any desire to prohibit dispatch into icing
conditions.
(2) Procedure. Since this condition assumes zero airspeed, wind tunnel testing
may be inappropriate unless conservative extrapolation of low speed tunnel data can be
determined to be valid. For protection schemes which are dependent primarily on
airspeed for proper functions (external screens have shown this tendency), it may be
necessary to verify adequate ground operation protection capability by very low speed
tunnels or by the use of outside facilities such as the Canadian National Research
Council’s spray rig at Ottawa, Canada. For heated systems or for internal bypass
schemes, tunnel speed may not be important, and adequate demonstration may be
accomplished at higher tunnel speeds provided that internal inlet airflows and heat
available are properly considered. Testing should proximate the regulatory test
conditions and be continued for 30 minutes using engine power and control
manipulation as normally accepted during taxiway operations, followed by an
acceleration to takeoff power. The test time may be shortened if de-ice or anti-ice
protection is adequate or if stabilization of ice build-up is affirmed. The induction system
should be in condition for safe flight at the conclusion of the test.
e. § 27.1093(c) Supercharged Reciprocating Engines.
(1) Explanation. This rule authorizes the designer to take credit for the
heat-of-compression available downstream of an engine air inlet supercharger to meet
the induction system heat rise requirements of § 27.1093(a)(3) or (a)(4), provided the
heat rise is automatically available for the applicable altitude and operating condition.
(2) Procedures. Since a wide variety of superchargers and supercharger
controls (waste-gate controls) have been devised, it is impracticable to outline specific
instructions for determining compliance. However, the certification engineer can
properly evaluate the arrangement by analyzing the system for trends (in heat rise
available) and conducting measurements to verify these trends and quantify the actual
values of heat rise available. Some factors to be considered are:
(i) Mechanically driven superchargers for rotorcraft usually operate over a
very narrow speed range, thus the heat of compression (∆ temperature) may remain
constant over the altitude range. Conversely, turbosuperchargers usually are controlled
(via waste-gate position modulation) to gradually increase the compression with
increase in altitude, thus the critical (or lowest) ∆ temperature may be available at very
low altitudes.
Page E - 112
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.