FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 531

PDF page 531 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 531
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

3/31/2014                                      AC 27-1B, Chg 4


                   (ii) Other waste-gate controllers sense carburetor deck pressure and
respond by modulating the waste gate to maintain a constant carburetor deck pressure
within the capabilities of the turbo unit. Heat of compression may then vary with altitude
and engine power in a complicated fashion such as to require experimental temperature
measurements across a wide range of operating conditions to determine compliance.

                    (iii) Turbosuperchargers which are not controlled (by waste-gate
modulation) but respond to an orificed exhaust generally will (at constant power)
produce more heat rise at altitude than at sea level; however, size matching between
engine and turbo unit may affect this. Instrumented flight tests should be used as a final
compliance verification method.

AC 27.1093A.  § 27.1093 (Amendment 27-23) INDUCTION SYSTEM ICING
            PROTECTION.

     a. Explanation. Amendment 27-23 clarifies that the phrase, “within the limitations
established for the rotorcraft” applies only to the requirement in § 27.1093(b)(1)(ii) for
demonstrating flight in falling and blowing snow.

 Procedures. All of the policy material for this section remains in effect with the update
that turbine engines and turbine engine inlets should perform satisfactorily in
atmospheric icing conditions defined in Appendix C of part 29. In addition to
section 27.1093 of this AC, the following procedures should be followed:

         (1) A “serious loss of power” in this section has been interpreted to be any
power loss that requires immediate pilot action. In addition, the term “adverse effect on
engine operation” in § 27.1093(b)(1)(ii) has been interpreted to be an effect that would
prevent the engine from achieving rated aircraft flight manual performance (takeoff,
climb, etc.). This term also includes effects on the engine induction system
characteristics to an acceptable level established by the engine manufacturer (inlet
distortion, etc.).

         (2) The applicant should show that rotorcraft prohibited from flight into falling
and blowing snow can exit inadvertent entrance into those conditions without adverse
effect upon the operating characteristics of the engine or the rotorcraft. This requires
that the engine and its inlet system be shown to operate satisfactorily throughout the
flight power range of the engine and within the operating limitations of the rotorcraft
during operation in the Inadvertent 1 mile visibility falling and blowing snow conditions
defined herein.

         (3) For unrestricted flight capability into Full snow conditions, both falling and
blowing, the applicant should show that each engine, and its inlet system, will operate
satisfactorily throughout the flight power range of the engine and within the operating
limitations of the rotorcraft. The applicant should show that any build-up or
accumulation of snow will not reduce or block the flow of inlet air to the engine. Any
accumulations that become dislodged should not affect engine operation.


                                                    Page E – 112.1

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →