FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-110

PDF page 528 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 528
AC 27-1B · E-110Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 4                                                     3/31/2014


                    (iii) Since during cruise in snow conditions the aircraft is likely to be in and
out of heavy snowfall, it is not practical for the crew to account for the time spent in
snow in level flight conditions. Thus, it is not appropriate to include time limitations in
the RFM for level flight snow operations.

               (iv) A practical ground and IGE hover time limitation of less than 25 minutes
in recirculating snow may be considered. The expected action at the expiration of this
specified time period would be shut down and inspection of the inlet system or transition
to a safe flight condition where demonstration has shown that moisture accumulations
will not intensify or shed and cause engine operational problems.

              (v) Artificially produced snow is an excellent development tool and has been
successfully used to indicate potential problem areas in induction systems. These
devices are usually restricted to use for hover and ground evaluations, and the snow
pellets produced by these machines are not sufficiently similar to natural snowflakes to
justify the use of artificial snow as the sole basis of certification.

         (4) Procedures.

                  (i) Satisfactory demonstration of the test conditions requires that the engine,
induction system, and proximate cowling surfaces remain free of excessive snow, ice,
or water accumulation. Excessive accumulation is defined as accumulation that may
cause engine instability, damage, or significant loss of engine power.  If a questionable
amount of snow or moisture accumulates in the inlet, the applicant may elect to
demonstrate that this amount in the form of snow or water and ice, as appropriate, can
be ingested by the engine without incurring surge, flameout, or damage.

                   (ii) The conditions specified assume actual flight demonstration in natural
snow. The ground operations and IGE hover test conditions assume operation in
recirculating snow. Blowing snow, resulting from rotor airflow recirculation, can be
expected to be more severe than natural blowing snow if the rotorcraft continues to
move slowly over freshly fallen snow. Thus, the blowing snow operational capability is
usually demonstrated by the taxi and hover operations in recirculating snow.

                    (iii) For VFR rotorcraft, the airspeeds for the level flight test condition should
include the maximum consistent with the visibility conditions. For IFR operations, the
airspeed should be the maximum cruise speed or the maximum speed specified for
snow operations in the flight manual limitations, unless other airspeeds are deemed
more critical.  It is recognized that many rotorcraft initially VFR certified are later IFR
certified with a resulting possible increase in airspeed in snow conditions. This factor
should be considered if IFR certification is anticipated.

               (iv) The visibility specified assumes that visual measurements are made in
falling snow in the absence of fog or recirculating snow by an observer at the test site
outside the tests rotorcraft’s area of influence. An accepted equation for relating this



Page E - 110

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →